Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model) › 2020.08–2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0444808 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model) J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model)  Electric Parking Brake does not Operate  


WIRING DIAGRAM

C402509E11
0.469,0.708 1.698,0.906 1.229,0.198 10 false ABS NO. 2 0.333,1.313 1.5,1.531 1.167,0.219 10 false ECU-IGR NO. 3 2.792,0.542 3.229,0.781 0.438,0.24 10 false +BS 2.813,1.156 3.25,1.396 0.438,0.24 10 false IGR 2.552,0.448 2.99,0.688 0.438,0.24 10 false 14 2.563,1.031 3,1.271 0.438,0.24 10 false 45 2.667,1.583 3.104,1.833 0.438,0.25 10 false A94 2.667,1.75 4.281,2.281 1.615,0.531 10 false Skid control ECU (Brake Actuator Assembly) 5.24,1.323 7.104,1.771 1.865,0.448 10 false Combination Meter Assembly 0.927,3.229 3.052,3.573 2.125,0.344 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>CALIBRATION

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks (red) when the ignition switch is first turned ON.



HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light (red) on the combination meter may be malfunctioning.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.VEHICLE OPERATION CHECK

B

2.VEHICLE OPERATION CHECK
a.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for 2WD)>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Lock and release operation is normal and parking brake indicator light turns off or blinks (red) A
Lock and release operation is malfunctioning and parking brake indicator light illuminates (red) or turns off according to switch operation B
Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks (red) C



A

3.INSPECT COMBINATION METER ASSEMBLY

B

INSPECT REAR BRAKE

C

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
3.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Park Warning
50004 409 108

b.

Check the combination meter assembly.

OK:

Parking brake indicator light (red) turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A94)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A94-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IGR TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A94)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A94-45 (IGR) - Body ground Ignition switch to ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR