Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093836 TELEMATICS _0444943 TELEMATICS SYSTEM(for Toyota Connected Services) C

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  B157011  Indicator (Red) Circuit Short to Ground  B157013  Indicator (Red) Circuit Open  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the ignition switch is turned to ON.

If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is set.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B157011 Indicator (Red) Circuit Short to Ground Manual (SOS) switch indicator (red) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telematics transceiver

·

Map light assembly

·

Harness or connector


Telematics A
B157013 Indicator (Red) Circuit Open Manual (SOS) switch indicator (red) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telematics transceiver

·

Map light assembly

·

Harness or connector


Telematics A

WIRING DIAGRAM

E427069E51
4.927,1.917 6.438,2.156 1.51,0.24 10 false Telematics Transceiver 4.927,1.74 6.917,1.938 1.99,0.198 10 false H85 5.177,0.792 6.5,1.135 1.323,0.344 10 false IND1 4.938,0.667 6.26,1.01 1.323,0.344 10 false 4 5.177,1.104 6.5,1.448 1.323,0.344 10 false SIG- 4.938,1.094 6.26,1.438 1.323,0.344 10 false 3 3.427,0.667 4.75,1.01 1.323,0.344 10 false 6 3.406,1.083 4.729,1.427 1.323,0.344 10 false 5 3.021,0.667 4.344,1.01 1.323,0.344 10 false IND1 2.948,1.094 4.271,1.438 1.323,0.344 10 false GND3 1.271,1.771 2.594,2.115 1.323,0.344 10 false V7 1.271,1.917 4.031,2.156 2.76,0.24 10 false Map Light Assembly (Manual (SOS) Switch)

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



HINT:

If DTC B157011 or B157013 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
B157011 or B157013 is output B
None of the above conditions are met C



A

B

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)

C

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)

Pre-procedure1

a.

Remove the map light assembly (manual (SOS) switch).

HINT:

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL



b.

Connect 2 dry-cell batteries (1.5 V each) in series.


Procedure1

a.
E434371C14
1.448,0.271 1.906,0.531 0.458,0.26 2.542,1.26 2.219,1.74 true 2.667,1.26 2.927,1.698 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.781,1.729 3.302,1.948 0.521,0.219 10 false GND3 2.01,1.76 2.448,1.969 0.438,0.208 10 false IND1 1.594,0.333 1.906,0.531 0.313,0.198 10 false V7
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Connect a positive (+) lead from the batteries to terminal 6 (IND1) and a negative (-) lead to terminal 5 (GND3) of the map light assembly (manual (SOS) switch) connector.


b.

Check if the manual (SOS) switch indicator (red) illuminates.

OK:

Manual (SOS) switch indicator (red) illuminates.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

Pre-procedure1

a.

Disconnect the H85 telematics transceiver connector.


b.

Disconnect the V7 map light assembly (manual (SOS) switch) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H85,V7)Location & Routing

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assembly

H85-4 (IND1) - V7-6 (IND1) Always Below 1 Ω
H85-4 (IND1) or V7-13 (IND1) - Body ground Always 10 kΩ or higher
H85-3 (SIG-) - V7-5 (GND3) Always Below 1 Ω
H85-3 (SIG-) or V7-5 (GND3) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT