This DTC is stored when a telephone microphone assembly signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B157213 | Microphone Circuit Open | Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON | ·
Telematics transceiver ·
Telephone microphone assembly ·
Harness or connector ·
Map light assembly |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System (for eCall).
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON and wait for 10 seconds or more.
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| B153711 or B153713 is output | B |
| None of the above conditions are met | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Pre-procedure1
Disconnect the H85 telematics transceiver connector.
Disconnect the V7 map light assembly (telephone microphone assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85,V7)Location & Routingewd_type=routing;type=c,c;code=H85,V7 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=5,6,7,23 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=16,15,14 |
||
| H85-5 (MCVD) - V7-16 (MACC) | Always | Below 1 Ω |
| H85-6 (MCI+) - V7-15 (MCO+) | Always | Below 1 Ω |
| H85-7 (MCI-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H85-5 (MCVD) or V7-16 (MACC) - Body ground | Always | 10 kΩ or higher |
| H85-6 (MCI+) or V7-15 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H85-7 (MCI-) or V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H85-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85)Location & Routingewd_type=routing;type=c;code=H85 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=5 |
||
| H85-5 (MCVD) - Body ground | Ignition switch ON | 4 to 6 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Remove the telephone microphone assembly.
Procedure1
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V7)Location & Routingewd_type=routing;type=c;code=V7 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=16,15,14 |
||
| V7-16 (MACC) - B-14 (MACC) | Always | Below 1 Ω |
| V7-15 (MCO+) - B-15 (MIC+) | Always | Below 1 Ω |
| V7-14 (MCO-) - B-16 (MIC-) | Always | Below 1 Ω |
| V7-16 (MACC) - V7-15 (MCO+) | Always | 10 kΩ or higher |
| V7-16 (MACC) - V7-14 (MCO-) | Always | 10 kΩ or higher |
| V7-15 (MCO+) - V7-14 (MCO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the telephone microphone assembly with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON and wait for 10 seconds or more.
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| B157213 is output | B |
| None of the above conditions are met | C |
A
B
C
Replace the telematics transceiver with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the telematics transceiver with a new one.
| Proceed to |
|---|
| NEXT |
NEXT