Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093836 TELEMATICS _0444943 TELEMATICS SYSTEM(for Toyota Connected Services) C

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  B15CB11  Telephone Main Antenna Circuit Short to Ground  B15CB13  Telephone Main Antenna Circuit Open  


DESCRIPTION

If an open or short circuit in the roof antenna assembly is detected as a result of a terminal check performed by the telematics transceiver, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15CB11 Telephone Main Antenna Circuit Short to Ground Roof antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Short circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly


Telematics A
B15CB13 Telephone Main Antenna Circuit Open Roof antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Open circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly


Telematics A

WIRING DIAGRAM

E434373E10
5.479,2.615 6.948,2.875 1.469,0.26 10 false Telematics Transceiver 5.313,0.99 5.927,1.188 0.615,0.198 10 false 1 5.292,1.573 5.906,1.771 0.615,0.198 10 false 1a 5.313,1.208 5.719,1.427 0.406,0.219 10 false E 3.813,0.99 4.427,1.188 0.615,0.198 10 false 1 3.781,1.583 4.396,1.781 0.615,0.198 10 false 1a 3.385,0.99 4,1.188 0.615,0.198 10 false 1 3.354,1.583 3.969,1.781 0.615,0.198 10 false 1a 3.365,1.208 3.604,1.396 0.24,0.188 10 false G 1.885,1.208 2.5,1.406 0.615,0.198 10 false H 2.156,2.156 3.427,2.5 1.271,0.344 10 false No. 2 Antenna Cord Sub-assembly 0.729,2.177 1.604,2.542 0.875,0.365 10 false Roof Antenna Assembly 4.094,2.146 5.271,2.583 1.177,0.438 10 false Antenna Cord Sub-assembly 5.313,1.792 5.719,2.01 0.406,0.219 10 false E 3.813,1.792 4.427,1.99 0.615,0.198 10 false F 3.823,1.208 4.438,1.406 0.615,0.198 10 false F 3.375,1.792 3.615,1.979 0.24,0.188 10 false G 1.885,1.792 2.5,1.99 0.615,0.198 10 false H 1.885,1.01 2.5,1.208 0.615,0.198 10 false 4 1.865,1.583 2.479,1.781 0.615,0.198 10 false 4a

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
B15CB11 or B15CB13 is output B
None of the above conditions are met C



A

B

3.INSPECT ROOF ANTENNA ASSEMBLY

C

3.INSPECT ROOF ANTENNA ASSEMBLY

Pre-procedure1

a.

Remove the roof antenna assembly.

HINT:

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ROOF ANTENNA>REMOVAL



Procedure1

a.
E271865C53
0.313,1 0.75,1.26 0.438,0.26 1.969,1.479 2.24,1.594 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.292,1.531 2.604,1.729 0.313,0.198 10 false 4a 0.49,1.063 0.646,1.26 0.156,0.198 10 false H
*a Component without harness connected
(Roof Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-4 - H-4a Always 4 to 11 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE ROOF ANTENNA ASSEMBLY

4.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.

Disconnect the No. 2 antenna cord sub-assembly from the roof antenna assembly connector.


b.

Disconnect the No. 2 antenna cord sub-assembly from the antenna cord sub-assembly connector.


Procedure1

a.
E434374C09
1.51,0.042 1.927,0.26 0.417,0.219 1.521,2.063 1.938,2.281 0.417,0.219 1.052,1.417 1.552,1.042 true 0.479,3.146 0.813,2.885 true 0.854,1.354 1.167,1.552 0.313,0.198 10 false 4a 0.281,3.104 0.594,3.302 0.313,0.198 10 false 1a 1.677,2.104 1.833,2.302 0.156,0.198 10 false G 1.688,0.083 1.844,0.281 0.156,0.198 10 false H 0.208,0.125 0.521,0.323 0.313,0.198 10 false *a 0.219,2.063 0.531,2.26 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Roof Antenna Assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-4 - G-1 Always Below 1 Ω
H-4a - G-1a Always Below 1 Ω
H-4 - G-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

5.INSPECT ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.

Disconnect the antenna cord sub-assembly connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna cord sub-assembly connector from the telematics transceiver.


Procedure1

a.
E434375C04
1.49,0.146 1.927,0.417 0.438,0.271 1.479,1.771 1.917,2.042 0.438,0.271 1.865,1.24 2.344,1.469 true 2.521,2.781 2.979,3.083 true 0.177,0.229 0.49,0.427 0.313,0.198 10 false *a 0.271,1.948 0.583,2.146 0.313,0.198 10 false *b 1.667,0.219 2.208,0.458 0.542,0.24 10 false E 1.677,1.844 2.219,2.083 0.542,0.24 10 false F 2.427,1.406 2.969,1.646 0.542,0.24 10 false 1a 3.073,3.031 3.427,3.302 0.354,0.271 10 false 1a
*a Front view of wire harness connector
(to No. 2 antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-1 - F-1 Always Below 1 Ω
E-1a - F-1a Always Below 1 Ω
E-1 or F-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.REPLACE TELEMATICS TRANSCEIVER

NG

6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT