Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3700E _57 Power Source / Network _093026 NETWORKING _0445204 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Battery ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Battery ECU Communication Stop Mode Communication stop for "HV/EV Battery" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Battery ECU assembly branch line or connector

·

Power source circuit of battery ECU assembly

·

Battery ECU assembly ground circuit

·

Battery ECU assembly



WIRING DIAGRAM

C427551E23
5.646,0.979 6.26,1.177 0.615,0.198 10 false CA2H 5.646,1.521 6.26,1.719 0.615,0.198 10 false CA2L 5.646,2.365 6.26,2.563 0.615,0.198 10 false AM 5.646,3.354 6.26,3.552 0.615,0.198 10 false IGCT 5.646,4.396 6.26,4.594 0.615,0.198 10 false GND 3.948,2.542 5.094,2.729 1.146,0.188 10 false ECU-B NO. 1 1.521,0.885 2.135,1.083 0.615,0.198 10 false 3 1.5,1.406 2.115,1.604 0.615,0.198 10 false 14 5.354,0.885 5.969,1.083 0.615,0.198 10 false 33 5.354,1.406 5.969,1.604 0.615,0.198 10 false 32 5.354,2.25 5.969,2.448 0.615,0.198 10 false 12 5.354,3.25 5.969,3.448 0.615,0.198 10 false 24 5.365,4.271 5.979,4.469 0.615,0.198 10 false 34 5.302,4.938 5.917,5.135 0.615,0.198 10 false z12 5.292,5.094 6.99,5.427 1.698,0.333 10 false Battery ECU Assembly 0.156,1.906 0.771,2.104 0.615,0.198 10 false O88 0.146,2.052 2.917,2.25 2.771,0.198 10 false No. 10 Global CAN Junction Connector 4.01,3.531 5.104,3.948 1.094,0.417 10 false IGCT NO. 2 1.708,2.344 3.323,2.552 1.615,0.208 10 false from Auxiliary Battery 1.99,3.333 3.427,3.573 1.438,0.24 10 false from IGCT Relay

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from the HV battery (traction battery assembly).

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly

-

Disconnecting the low voltage connector of the HV battery (traction battery assembly)

-

Disconnecting the low voltage connector of the electric vehicle charger sub-assembly


·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery (traction battery assembly), put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A371654C03
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly.


·

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (BATTERY ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the z12 battery ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-33 (CA2H) - z12-32 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BATTERY ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-34 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-12 (AM) - Body ground Ignition switch off 11 to 14 V
z12-24 (IGCT) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)