Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3700E _57 Power Source / Network _093026 NETWORKING _0445205 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Transmission Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Transmission Control ECU Communication Stop Mode Communication stop for "TCM" is indicated on the "Communication Bus Check" screen of the GTS.
Click here
(Click here)
·

TCM branch line or connector

·

Power source circuit of TCM

·

TCM ground circuit

·

TCM



WIRING DIAGRAM

C366177E30
1.667,0.51 1.823,0.708 0.156,0.198 10 false 4 1.635,1.042 1.969,1.292 0.333,0.25 10 false 15 0.188,1.573 0.604,1.781 0.417,0.208 10 false H117 0.188,1.75 3.063,2 2.875,0.25 10 false No. 6 Global CAN Junction Connector 5.531,0.51 5.781,0.708 0.25,0.198 10 false 15 5.521,1.042 5.771,1.24 0.25,0.198 10 false 16 5.781,0.635 6.365,0.833 0.583,0.198 10 false CANH 5.792,1.188 6.375,1.385 0.583,0.198 10 false CANL 5.792,2.24 6.167,2.531 0.375,0.292 10 false +B 5.781,2.781 6.417,3.083 0.635,0.302 10 false IGSW 5.792,3.302 6.208,3.552 0.417,0.25 10 false E1 6.021,3.74 6.531,4.042 0.51,0.302 10 false D71 6.01,3.917 7.052,4.469 1.042,0.552 10 false TCM 5.573,2.125 5.823,2.323 0.25,0.198 10 false 1 5.521,2.667 5.781,2.875 0.26,0.208 10 false 41 5.583,3.188 5.833,3.385 0.25,0.198 10 false 2 4.5,2.396 5.24,2.604 0.74,0.208 10 false EFI NO. 5 4.313,2.927 5.375,3.146 1.063,0.219 10 false ECU-IGP NO. 1 1.813,2.229 3.563,2.469 1.75,0.24 10 false from EFI-MAIN NO. 1 Relay 2.573,2.76 4,2.979 1.427,0.219 10 false from IGP Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (TCM BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C392554C41
1.583,0.188 2,0.438 0.417,0.25 2.938,1.896 2.427,0.99 true 1.229,1.896 2.333,0.979 true 0.177,0.115 0.438,0.354 0.26,0.24 10 false *a 1.677,0.229 2.083,0.479 0.406,0.25 10 false D71 2.99,1.823 3.396,2.031 0.406,0.208 10 false CANL 0.792,1.823 1.302,2.073 0.51,0.25 10 false CANH
*a Front view of wire harness connector
(to TCM)


Disconnect the D71 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D71)Location & Routing

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D71-15 (CANH) - D71-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TCM)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the D71 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D71)Location & Routing

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D71-2 (E1) -Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D71)Location & Routing

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D71-1 (+B) - Body ground Ignition switch ON 11 to 14 V
D71-41 (IGSW) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)