Home › Drivetrain › K320 (MULTIDRIVE / CVT) › TCM
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438040 TCM A

K320 MULTIDRIVE / CVT  TCM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446840N02
5.083,2.927 5.083,3.344 false 6.49,0.25 6.823,0.25 false 6.479,0.677 6.813,0.677 false 1.292,1.844 1.292,2.26 false 1.229,2.271 1.51,2.625 0.281,0.354 18 false 3 5.031,3.385 5.313,3.74 0.281,0.354 18 false 4 6.323,0.094 6.604,0.448 0.281,0.354 18 false 1 2.125,2.802 2.438,3 0.313,0.198 10 false x4 2.979,2.969 3.292,3.167 0.313,0.198 10 false x4 3.667,2.802 3.979,3 0.313,0.198 10 false x9 5.948,2.542 6.26,2.74 0.313,0.198 10 false x2 6.313,0.521 6.594,0.875 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
4 ENGINE UNDER COVER LH 51442C - - -

C446841N03
1.938,1.083 2.271,1.083 false 1.958,1.771 2.292,1.771 false 2.031,2.583 2.365,2.583 false 4.563,1.073 4.896,1.073 false 5.677,2.208 6.01,2.208 false 2.323,0.948 2.604,1.302 0.281,0.354 18 false 5 2.375,1.625 2.656,1.979 0.281,0.354 18 false 6 2.458,2.458 2.74,2.813 0.281,0.354 18 false 7 5.385,1.583 5.635,1.75 0.25,0.167 10 false x3 4.365,0.917 4.646,1.271 0.281,0.354 18 false 8 6.083,2.063 6.365,2.417 0.281,0.354 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

5 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
6 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
7 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
8 ECM 89661 - - -
9 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -

C429248N04
4.865,4.333 5.115,4.625 5.115,4.625 5.281,4.625 false 5.625,4.052 6.042,4.552 6.042,4.552 6.292,4.552 false 3.792,4.563 4.208,5.063 4.208,5.063 4.458,5.063 false 6.073,3.573 6.385,3.771 0.313,0.198 10 false x2 3.167,4.896 3.479,5.094 0.313,0.198 10 false x2 5.583,4.5 6.042,4.833 0.458,0.333 18 false 10 6.323,4.417 6.781,4.75 0.458,0.333 18 false 11 4.51,4.917 4.969,5.25 0.458,0.333 18 false 12

Procedure Part Name Code
Z101186

Z101188

Z101187

10 TCM 89535B (Click here) - -
11 NO. 1 TRANSMISSION CONTROL ECU BRACKET 89539M - - -
12 NO. 2 TRANSMISSION CONTROL ECU BRACKET 89539N - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the TCM removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Air intake system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
TCM
If transaxle compensation code read from TCM:
1.

Transfer transaxle compensation code

2.

Perform reset memory

3.

CVT oil pressure calibration

4.

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:
(Click here)
If transaxle compensation code not read from TCM:
1.

Reset transaxle compensation code

2.

Perform reset memory

3.

CVT oil pressure calibration

4.

Perform road test to allow TCM to learn


Update ECU security key

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 51410 3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 4.REMOVE ENGINE UNDER COVER LH

Hide 5.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 6.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 7.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 9.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 89535B 10.REMOVE TCM

a.
C431106C01
0.583,0.083 0.75,0.417 0.167,0.333 18 true i 3.917,0.083 4.167,0.417 0.25,0.333 18 true ii 2.25,2.083 2.5,2.417 0.25,0.333 18 true iii
V113147

Remove in this Direction - -


i.

Disengage the clamp to disconnect the engine wire from the No. 2 transmission control ECU bracket.


ii.

Disengage the claw, rotate the lever and disconnect the TCM connector.


iii.

Remove the 2 bolts and TCM from the continuously variable transaxle assembly.



Hide 89539M 11.REMOVE NO. 1 TRANSMISSION CONTROL ECU BRACKET

a.
C431107


Hide 89539N 12.REMOVE NO. 2 TRANSMISSION CONTROL ECU BRACKET

a.
C431108