Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM3700E _57 Power Source / Network _093026 NETWORKING _0445204 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Rear Motor Generator Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Rear Motor Generator Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Rear Motor Generator" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)


·

Rear hybrid motor control inverter assembly branch line or connector

·

Power source circuit of rear hybrid motor control inverter assembly

·

Rear hybrid motor control inverter assembly ground circuit

·

Rear hybrid motor control inverter assembly



WIRING DIAGRAM

C440253E01
0.188,1.792 3.021,2.125 2.833,0.333 10 false No. 10 CAN Junction Connector 0.188,1.625 0.635,1.802 0.448,0.177 10 false O88 1.594,1.125 1.917,1.292 0.323,0.167 10 false 13 1.604,0.583 1.813,0.75 0.208,0.167 10 false 2 5.49,0.594 5.719,0.771 0.229,0.177 10 false 10 5.75,0.729 6.208,0.906 0.458,0.177 10 false PCNH 3.979,2.927 4.563,3.125 0.583,0.198 10 false PCU RR 1.771,2.74 3.323,3.021 1.552,0.281 10 false from Auxiliary Battery 5.74,4.396 6.292,4.573 0.552,0.177 10 false GNR2 5.427,4.833 5.833,5.01 0.406,0.177 10 false O74 5.427,5.01 7.031,5.427 1.604,0.417 10 false Rear Hybrid Motor Control Inverter Assembly 5.75,1.26 6.167,1.438 0.417,0.177 10 false PCNL 5.563,2.667 5.708,2.833 0.146,0.167 10 false 6 5.5,3.188 5.719,3.365 0.219,0.177 10 false 13 5.573,4.25 5.729,4.427 0.156,0.177 10 false 7 5.75,3.313 6.156,3.49 0.406,0.177 10 false +BR2 5.49,1.115 5.719,1.292 0.229,0.177 10 false 11 5.74,3.844 6.198,4.021 0.458,0.177 10 false GNR1 5.573,3.719 5.729,3.896 0.156,0.177 10 false 1 5.75,2.781 6.156,2.958 0.406,0.177 10 false +BR1

CAUTION / NOTICE / HINT

CAUTION:
1.
A340358


2.

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery

*: for AWD



3.
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

4.
A358042

After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

5.
A357589C73
1.563,0.708 1.813,0.417 true 1.844,0.302 2.156,0.5 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.

*: for AWD





CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the O74 rear hybrid motor control inverter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-10 (PCNH) - O74-11 (PCNL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-1 (GNR1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
O74-7 (GNR2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O74)Location & Routing

Click Connector(O74)Body>Floor Wire>Rear Hybrid Motor Control Inverter Assembly

O74-6 (+BR1) - Body ground Ignition switch ON 11 to 14 V
O74-13 (+BR2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR HYBRID MOTOR CONTROL INVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)