Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2020.08–2021.07
RM3700E _56 Audio / Visual / Telematics _093687 NAVIGATION / MULTI INFO DISPLAY _0441739 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15DB  Telematics Transceiver Disconnected  


DESCRIPTION

If the radio and display receiver assembly cannot detect the telematics transceiver for a certain period of time (90 seconds) after the ignition switch is turned ACC and the radio and display receiver assembly confirms that the information is missing by checking past telematics transceiver recognition information (registered information), this DTC will be stored.

HINT:

The telematics system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the telematics system will not operate normally.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15DB Telematics Transceiver Disconnected Telematics transceiver disconnected
·

Harness or connector

·

Telematics transceiver

·

Navigation ECU

·

Radio and display receiver assembly


Navigation System A

HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.


WIRING DIAGRAM

E450815E01
1.427,0.563 1.583,0.76 0.156,0.198 10 false 1 2.917,0.781 4.385,1.021 1.469,0.24 10 false from Auxiliary Battery 1,0.781 1.208,0.969 0.208,0.188 10 false +B 1.333,0.771 1.646,0.938 0.313,0.167 10 false H85 2.135,0.927 2.51,1.167 0.375,0.24 10 false DCM 1.406,1.542 1.615,1.729 0.208,0.188 10 false 19 1.354,1.729 1.667,1.896 0.313,0.167 10 false H85 0.958,1.74 1.208,1.927 0.25,0.188 10 false IG2 2.896,1.74 4.365,1.979 1.469,0.24 10 false from IGR-NO. 2 Relay 1.76,1.906 2.781,2.104 1.021,0.198 10 false ECU-IGR NO. 2 1.396,2.375 1.604,2.563 0.208,0.188 10 false 20 1.083,2.604 1.24,2.792 0.156,0.188 10 false E 1.344,2.583 1.656,2.75 0.313,0.167 10 false H85 3.146,3.313 3.302,3.51 0.156,0.198 10 false 2 1.417,3.26 1.573,3.458 0.156,0.198 10 false 1 0.854,3.469 1.25,3.656 0.396,0.188 10 false USB- 3.354,3.49 3.75,3.677 0.396,0.188 10 false US4- 1.302,3.469 1.698,3.667 0.396,0.198 10 false H119 3.167,3.75 3.323,3.948 0.156,0.198 10 false 1 1.406,3.677 1.563,3.875 0.156,0.198 10 false 2 0.833,3.885 1.25,4.083 0.417,0.198 10 false USB+ 3.365,3.896 3.813,4.104 0.448,0.208 10 false US4+ 1.302,3.885 1.698,4.083 0.396,0.198 10 false H119 3.156,4.167 3.313,4.365 0.156,0.198 10 false 3 1.417,4.115 1.573,4.313 0.156,0.198 10 false 3 2.438,4.177 2.594,4.375 0.156,0.198 10 false * 1.302,4.302 1.698,4.5 0.396,0.198 10 false H119 3.344,4.302 3.792,4.51 0.448,0.208 10 false UGD4 0.802,4.281 1.25,4.49 0.448,0.208 10 false USBS 3.375,4.667 3.771,4.865 0.396,0.198 10 false H131 3.365,4.844 4.396,5.063 1.031,0.219 10 false Navigation ECU 1.385,5.156 1.573,5.344 0.188,0.188 10 false 15 4.813,5.26 5,5.448 0.188,0.188 10 false 10 0.792,5.365 1.24,5.573 0.448,0.208 10 false USBV 1.333,5.365 1.646,5.531 0.313,0.167 10 false H85 5.063,5.396 5.51,5.604 0.448,0.208 10 false USBV 1.385,5.604 1.573,5.792 0.188,0.188 10 false 31 4.813,5.719 5,5.906 0.188,0.188 10 false 11 0.792,5.802 1.24,6.01 0.448,0.208 10 false USBG 1.323,5.813 1.635,6.01 0.313,0.198 10 false H85 5.063,5.813 5.51,6.021 0.448,0.208 10 false USBG 4.74,6.219 5.135,6.417 0.396,0.198 10 false H81 4.74,6.396 6.438,6.802 1.698,0.406 10 false Radio and Display Receiver Assembly 0.063,6.479 1.521,6.708 1.458,0.229 10 false Telematics Transceiver 0.698,7.01 2.156,7.24 1.458,0.229 10 false *: Shielded 1.302,7.375 3.99,7.615 2.688,0.24 10 false : Data Signal (USB Communication Line)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the telematics transceiver, make sure to replace it with a new one.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for G-BOOK.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch ON and wait for 90 seconds.


c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)

Pre-procedure1

a.

Disconnect the H85 telematics transceiver connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H85)Location & Routing

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

H85-20 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H85)Location & Routing

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

H85-1 (+B) - Body ground Ignition switch off 11 to 14 V
H85-19 (IG2) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

Pre-procedure1

a.

Disconnect the radio and display receiver assembly connector.


Procedure1

b.
E367494C89
1.542,0.75 1.958,1.021 0.417,0.271 2.438,2.844 1.844,2.052 true 1.26,2.813 1.531,2.052 true 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a 1.615,0.792 2.052,0.979 0.438,0.188 10 false H81 2.292,2.875 2.906,3.073 0.615,0.198 10 false USBV 1.021,2.875 1.635,3.073 0.615,0.198 10 false USBG
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H81)Location & Routing

Click Connector(H81)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H81-11 (USBG) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H81)Location & Routing

Click Connector(H81)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H81-10 (USBV) - H81-11 (USBG) Ignition switch ACC 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

Pre-procedure1

a.

Disconnect the H81 radio and display receiver assembly connector.


b.

Disconnect the H85 telematics transceiver connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H81,H85)Location & Routing

Click Connector(H81)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

H81-10 (USBV) - H85-15 (USBV) Always Below 1 Ω
H81-11 (USBG) - H85-31 (USBG) Always Below 1 Ω
H81-10 (USBV) - Body ground Always 10 kΩ or higher
H81-11 (USBG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

6.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - NAVIGATION ECU)

Pre-procedure1

a.

Disconnect the H119 telematics transceiver connector.


b.

Disconnect the H131 navigation ECU connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H119,H131)Location & Routing

Click Connector(H119)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

Click Connector(H131)Instrument Panel>Instrument Panel Wire / Speaker Wire>Navigation ECU

H119-1 (USB-) - H131-2 (US4-) Always Below 1 Ω
H119-2 (USB+) - H131-1 (US4+) Always Below 1 Ω
H119-3 (USBS) - H131-3 (USD4) Always Below 1 Ω
H119-1 (USB-) - Body ground Always 10 kΩ or higher
H119-2 (USB+) - Body ground Always 10 kΩ or higher
H119-3 (USBS) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

7.CHECK TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch ON and wait for 90 seconds.


c.

Recheck for DTCs and check that no DTCs are output.

Click here

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

10.CHECK NAVIGATION ECU

B

END (TELEMATICS TRANSCEIVER IS DEFECTIVE)

10.CHECK NAVIGATION ECU
a.

Replace the navigation ECU with a new one.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL



Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
11.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch ON and wait for 90 seconds.


c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END (NAVIGATION ECU IS DEFECTIVE)