Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443940 FRONT SEAT SIDE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

B574506C02
3.615,1.938 3.615,2.271 false 2.552,0.677 2.885,0.677 false 6.177,1.604 6.51,1.604 false 0.802,2.135 0.802,2.469 false 4.698,0.823 4.698,1.156 false 3.583,2.271 3.74,2.469 0.156,0.198 10 false ● 1.448,1.406 1.76,1.604 0.313,0.198 10 false x2 1.74,1.188 2.052,1.385 0.313,0.198 10 false x2 4.667,1.167 4.823,1.365 0.156,0.198 10 false ● 3.365,1.896 3.677,2.094 0.313,0.198 10 false x2 4.75,0.771 5.063,0.969 0.313,0.198 10 false x2 0.729,2.479 1.323,2.771 0.594,0.292 18 false 1 6.521,1.479 7.115,1.771 0.594,0.292 18 false 2 2.333,0.552 2.927,0.844 0.594,0.292 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 SEPARATE TYPE FRONT SEATBACK COVER WITH PAD - - - -
2 FRONT SEAT AIRBAG ASSEMBLY 73910A - - -
3 FRONT SEAT CENTER AIRBAG ASSEMBLY 739H0 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front seat airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
B475753

Be sure to read precaution thoroughly before servicing.

·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



NOTICE:

If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

·

Front seat assembly (for Manual seat):

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY

·

Front seat assembly (for Power seat):

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


Hide 73910A 2.REMOVE FRONT SEAT AIRBAG ASSEMBLY

CAUTION:
B399378C01
0,0 0,0 false
V100155

Deployment Side


·

When storing the front seat airbag assembly, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.
B583379

Disengage the clamp.


b.

Remove the 2 nuts and front seat airbag assembly.

CAUTION:
·

Do not reuse the nut.

·

If the installation surface or surrounding area of the front seat airbag assembly is deformed or damaged, replace the front seatback frame sub-assembly with a new one.




Hide 739H0 3.REMOVE FRONT SEAT CENTER AIRBAG ASSEMBLY

CAUTION:
B399378C01
0,0 0,0 false
V100155

Deployment Side


·

When storing the front seat center airbag assembly, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.
B583378

Disengage the clamp.


b.

Remove the 2 nuts and front seat center airbag assembly.

CAUTION:
·

Do not reuse the nut.

·

If the installation surface or surrounding area of the front seat center airbag assembly is deformed or damaged, replace the front seat center airbag assembly with a new one.