When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light switch assembly and turns on the stop lights.
Pre-collision brake is operating.
The dynamic radar cruise control system is operating and is applying the brakes.
Secondary collision brake is operating.
Brake hold is operating.
The parking brake is engaged while the vehicle is being driven.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C13807E | Stop Lamp Relay Actuator Stuck On | When the IGR terminal voltage exceeds 10 V and the +BS terminal voltage is 9.5 V or higher, stop light drive output (STPO) is OFF, STP is OFF and STP2 is ON continuously for 5 seconds or more. | ·
Wire harness and connector ·
Skid control ECU (Brake actuator assembly) ·
Rear combination light assembly LH ·
Rear combination light assembly RH ·
Center stop light assembly |
Brake/EPB | A |
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| for Halogen Headlight | A |
| for LED Headlight | B |
A
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A63 stop light switch assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure2
Turn the ignition switch to ON.
Procedure3
Check the illumination status of the brake lights.
| Result | Proceed to |
|---|---|
| The stop lights are illuminated | A |
| The stop lights are not illuminated | B |
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
Reconnect the A63 stop light switch assembly connector.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay | STP2 terminal input | OFF / ON | OFF: STP2 terminal input OFF
ON: STP2 terminal input ON |
|
| Tester Display |
|---|
| Stop Light Relay |
With the brake pedal released, check the value of Data List item "Stop Light Relay".
| Result | Proceed to |
|---|---|
| The value of Stop Light Relay is OFF | A |
| The value of Stop Light Relay is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the O102 rear combination light assembly LH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay | STP2 terminal input | OFF / ON | OFF: STP2 terminal input OFF
ON: STP2 terminal input ON |
|
| Tester Display |
|---|
| Stop Light Relay |
With the brake pedal released, check the value of Data List item "Stop Light Relay".
| Result | Proceed to |
|---|---|
| The value of Stop Light Relay is OFF | A |
| The value of Stop Light Relay is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the O104 rear combination light assembly RH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay | STP2 terminal input | OFF / ON | OFF: STP2 terminal input OFF
ON: STP2 terminal input ON |
|
| Tester Display |
|---|
| Stop Light Relay |
With the brake pedal released, check the value of Data List item "Stop Light Relay".
| Result | Proceed to |
|---|---|
| The value of Stop Light Relay is OFF | A |
| The value of Stop Light Relay is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the Q1 center stop light assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay | STP2 terminal input | OFF / ON | OFF: STP2 terminal input OFF
ON: STP2 terminal input ON |
|
| Tester Display |
|---|
| Stop Light Relay |
With the brake pedal released, check the value of Data List item "Stop Light Relay".
| Result | Proceed to |
|---|---|
| The value of Stop Light Relay is OFF | A |
| The value of Stop Light Relay is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure2
Turn the ignition switch to ON.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A94)Location & Routingewd_type=routing;type=c;code=A94 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=37 |
||
| A94-37 (STP2) - Body ground | Ignition switch ON | 0 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure2
Turn the ignition switch to ON.
Procedure3
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63,A94)Location & Routingewd_type=routing;type=c,c;code=A63,A94 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=4 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=32 |
||
| A63-4 (ACC) or A94-32 (STPO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A63 stop light switch assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure2
Turn the ignition switch to ON.
Procedure3
Check the illumination status of the brake lights.
| Result | Proceed to |
|---|---|
| The stop lights are illuminated | A |
| The stop lights are not illuminated | B |
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
Reconnect the A63 stop light switch assembly connector.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay | STP2 terminal input | OFF / ON | OFF: STP2 terminal input OFF
ON: STP2 terminal input ON |
|
| Tester Display |
|---|
| Stop Light Relay |
With the brake pedal released, check the value of Data List item "Stop Light Relay".
| Result | Proceed to |
|---|---|
| The value of Stop Light Relay is OFF | A |
| The value of Stop Light Relay is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the O106 rear combination light assembly LH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay | STP2 terminal input | OFF / ON | OFF: STP2 terminal input OFF
ON: STP2 terminal input ON |
|
| Tester Display |
|---|
| Stop Light Relay |
With the brake pedal released, check the value of Data List item "Stop Light Relay".
| Result | Proceed to |
|---|---|
| The value of Stop Light Relay is OFF | A |
| The value of Stop Light Relay is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the O109 rear combination light assembly RH connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay | STP2 terminal input | OFF / ON | OFF: STP2 terminal input OFF
ON: STP2 terminal input ON |
|
| Tester Display |
|---|
| Stop Light Relay |
With the brake pedal released, check the value of Data List item "Stop Light Relay".
| Result | Proceed to |
|---|---|
| The value of Stop Light Relay is OFF | A |
| The value of Stop Light Relay is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the Q1 center stop light assembly connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Operate the GTS to check the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay | STP2 terminal input | OFF / ON | OFF: STP2 terminal input OFF
ON: STP2 terminal input ON |
|
| Tester Display |
|---|
| Stop Light Relay |
With the brake pedal released, check the value of Data List item "Stop Light Relay".
| Result | Proceed to |
|---|---|
| The value of Stop Light Relay is OFF | A |
| The value of Stop Light Relay is ON | B |
Post-procedure1
Turn the ignition switch off.
A
B
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure2
Turn the ignition switch to ON.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A94)Location & Routingewd_type=routing;type=c;code=A94 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=37 |
||
| A94-37 (STP2) - Body ground | Ignition switch ON | 0 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure2
Turn the ignition switch to ON.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63,A94)Location & Routingewd_type=routing;type=c,c;code=A63,A94 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=4 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=32 |
||
| A63-4 (ACC) or A94-32 (STPO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG