Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0444806 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C14D71C  Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

This DTC is stored when the skid control ECU (brake actuator assembly) receives a sensor supply voltage malfunction signal from the acceleration sensor (airbag sensor assembly).

This DTC may be stored due to an intermittent low power source voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C14D71C Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range When the +BS terminal voltage is from 9.5 to 17.4 V at a vehicle speed exceeding 3 km/h (2 mph), an acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

Wire harness and connector

·

Acceleration sensor (airbag sensor assembly)


Brake/EPB A

WIRING DIAGRAM

C400839E32
0.823,1.313 1.438,1.51 0.615,0.198 10 false CAFL 6.042,1.323 6.656,1.521 0.615,0.198 10 false CANL 0.802,0.74 1.417,0.938 0.615,0.198 10 false CAFH 6.042,0.698 6.656,0.896 0.615,0.198 10 false CANH 0.927,1.948 1.385,2.146 0.458,0.198 10 false IGR 2.125,2.104 3.021,2.292 0.896,0.188 10 false A/BAG-IGR 3.958,1.938 5.542,2.438 1.583,0.5 10 false from IGR-NO. 1 Relay 1,2.573 1.313,2.771 0.313,0.198 10 false E1 1,3.177 1.313,3.375 0.313,0.198 10 false E2 0.115,3.865 1.792,4.49 1.677,0.625 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.115,3.708 0.573,3.906 0.458,0.198 10 false H14 2.802,4.375 4.677,4.74 1.875,0.365 10 false : CAN Communication Line 5.521,4.125 7.083,4.594 1.563,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 5.521,3.958 5.979,4.156 0.458,0.198 10 false A94 5.771,1.135 6.083,1.333 0.313,0.198 10 false 43 5.771,0.521 6.083,0.719 0.313,0.198 10 false 27 1.281,0.552 1.594,0.75 0.313,0.198 10 false 26 1.292,1.167 1.604,1.365 0.313,0.198 10 false 27 1.292,1.823 1.604,2.021 0.313,0.198 10 false 36 1.292,2.448 1.604,2.646 0.313,0.198 10 false 33 1.281,3.052 1.594,3.25 0.313,0.198 10 false 32

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the yaw rate and acceleration sensor (airbag sensor assembly) was replaced or reinstalled, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the H14 yaw rate and acceleration sensor (airbag sensor assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure3

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H14)Location & Routing

Click Connector(H14)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Sensor Assembly

H14-36 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

2.CHECK HARNESS AND CONNECTOR (E1 AND E2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (E1 AND E2 TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H14)Location & Routing

Click Connector(H14)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Sensor Assembly

H14-33 (E1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω
H14-32 (E2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC

Pre-procedure1

a.

Reconnect the H14 yaw rate and acceleration sensor (airbag sensor assembly) connector.


Procedure1

a.

Operate the GTS to clear the codes.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Operate the GTS to read the DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C14D71C is not output A
C14D71C is output B



Post-procedure1

a.

None



A

B