Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443941 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B592980N01
6.458,0.594 6.792,0.594 false 2.781,3.781 3.115,3.781 false 6.49,0.26 6.823,0.26 false 6.385,3.094 6.719,3.094 false 1.917,1.042 2.25,1.042 false 6.323,0.125 6.604,0.479 0.281,0.354 18 false 1 6.302,0.458 6.583,0.813 0.281,0.354 18 false 2 6.76,2.948 7.042,3.302 0.281,0.354 18 false 3 2.604,3.635 2.885,3.99 0.281,0.354 18 false 4 2.583,0.906 2.865,1.26 0.281,0.354 18 false 5 2.271,4.396 2.583,4.594 0.313,0.198 10 false x2 1.26,0.76 1.573,0.958 0.313,0.198 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 REAR CONSOLE BOX ASSEMBLY 58910C - - -
4 FRONT FLOOR CARPET ASSEMBLY 58510D - - -
5 AIRBAG ECU ASSEMBLY 89170A (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the center airbag sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B473126

Be sure to read Precaution thoroughly before servicing.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 58910C 3.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 58510D 4.REMOVE FRONT FLOOR CARPET ASSEMBLY

a.
B592981


Hide 89170A 5.REMOVE AIRBAG ECU ASSEMBLY

a.
B596997C01
1.677,0.802 0.677,0.802 true 0.5,0.708 0.813,0.865 0.313,0.156 10 false *a 4.615,0.104 4.896,0.458 0.281,0.354 18 false ii 0.167,0.094 0.448,0.448 0.281,0.354 18 false i 0.354,1.771 0.729,2.01 0.375,0.24 12 false *A 2.729,1.813 3.104,2.052 0.375,0.24 12 false *B
*A w/ Smart Entry and Start System *B w/o Smart Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B592995N01
0.458,0.115 0.74,0.469 0.281,0.354 18 false i 4.344,0.083 4.625,0.438 0.281,0.354 18 false ii

i.

Pull out each connector with its connector lock pushed to disconnect the 3 connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



ii.

Remove the 3 bolts and airbag ECU assembly.

NOTICE:

If the airbag ECU assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the airbag ECU assembly with a new one.