Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0444806 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) L

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  PRECAUTION  


TROUBLESHOOTING PRECAUTION


a.

When there is a malfunction with terminal contact points or part installation problems, removal and installation of the suspected problem parts may return the system to the normal condition either completely or temporarily.


b.

Before disconnecting a connector or removing and installing a component in order to narrow down the malfunctioning part, make sure to perform the following procedure.

·

Check for and record any DTCs and Freeze Frame Data that were stored around the time that the malfunction occurred.

·

If any open circuit DTCs related to intermittent (momentary interruptions) malfunctions are output, check the intermittent monitor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>CHECK FOR INTERMITTENT PROBLEMS


NOTICE:

Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more*.

*: Differs according to vehicle conditions




c.

Since the system may be influenced by malfunctions in systems other than the brake control system, be sure to check for DTCs in other systems.



HANDLING PRECAUTION


a.

Always ensure that the ignition switch is off before removing the brake actuator assembly or a sensor unless specifically instructed by the repair manual.


b.

When replacing the brake actuator assembly, always replace it with a new one.

NOTICE:

Never use a brake actuator assembly from another vehicle, including new vehicles.



c.

When replacing the brake actuator assembly, always check that ECU security key is registered.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY


d.

If the brake actuator assembly or a sensor has been removed and installed, always perform a Dealer Mode (Signal Check) inspection and check for DTCs after completion of installation to confirm that the system is operating correctly.


e.

Do not remove and install any electronically controlled brake system components not specified by the repair manual or the system may not operate correctly due to loss of calibration.


f.

When performing diagnosis and repair for the electronically controlled brake system, follow all specified procedures and perform the necessary inspections after completion.



DTC PRECAUTION


a.

If the warning lights are illuminated due to a malfunction, the warning lights will only turn off for some DTCs when the malfunction is repaired and the DTCs are cleared.


b.

If a warning lights are illuminated, it is necessary to follow the procedure to turn off the warning lights.

Warning Clearing Procedure
DTC No. Procedure
C05001F
C050023
C05003A
C05061F
C050623
C05063A
C050C1F
C050C23
C050C3A
C05121F
C051223
C05123A
C05201C
C052096
1.

Repair or replace with new part

2.

Turn the ignition switch to ON

3.

Drive (30 km/h (19 mph) or higher for 30 seconds) → Warning light turns off


C13807E
C13807F
P057111
1.

Repair or replace with new part

2.

Turn the ignition switch to ON and stop the vehicle for 5 seconds or more, and then lightly depress the brake pedal 2 or 3 times → Warning light turns off


C052696
C14FE14
1.

Repair or replace with new part

2.

Turn the ignition switch to ON, and idling for 3 seconds → Warning light turns off


C006396
1.

Repair or replace with new part

2.

Turn the ignition switch to ON, and idling for 10 seconds → Warning light turns off



NOTICE:
·

Use caution when operating the vehicle when the warning lights are illuminated as the system may not operate due to a fail-safe function.

·

After clearing the DTCs, the DTCs will be stored again if the malfunction persists.





PRECAUTION FOR REPLACE STEERING SENSOR


NOTICE:

After replacing the steering sensor, check that ECU security key is registered.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



CHASSIS DYNAMOMETER PRECAUTION


When testing with a 2-wheel drum tester such as a speedometer tester, combination tester for the speedometer and brakes, or chassis dynamometer, or when jacking up the front wheels and turning the wheels, perform the following procedure to enter Inspection Mode and disable the TRC and VSC systems.

CAUTION:
·
C342048

Do not use the drum tester with any of the lock chains disconnected.

·

Using the drum tester with a lock chain disconnected could cause the vehicle to begin moving unexpectedly.

·
C342047

Do not use the drum tester while the TRC or VSC is able to operate.

·

TRC or VSC operation could cause the vehicle to begin moving unexpectedly.



NOTICE:

Secure the vehicle with lock chains for safety.


HINT:

If Inspection Mode is not used, the vehicle may unexpectedly move off the dynamometer because of TRC and VSC operation.


a.

Activating Inspection Mode (When Using the GTS)

i.

Ensure that the ignition switch is off and the engine is stopped.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Operate the GTS to enter the Inspection Mode.

Chassis > Brake/EPB > Utility
Tester Display
Inspection Mode
50005 435 4555

vi.

Check that the VSC OFF indicator light comes on and the TRC OFF message is displayed on the multi-information display.

NOTICE:

Turn the ignition switch off when 60 seconds or more have elapsed since Inspection Mode was entered. If the ignition switch is turned off before 60 seconds or more elapse, Inspection Mode continues when the ignition switch is turned to ON.


HINT:
·

If the VSC OFF indicator light does not come on and the TRC OFF message is not displayed on the multi-information display, repeat the steps above.

·

Turning the ignition switch off ends Inspection Mode.





b.

Activating Inspection Mode (When not Using the GTS)

HINT:

Perform steps "C" to "G" within 30 seconds.


i.

Ensure that the ignition switch is off and the engine is stopped (Step "A").


ii.

Release the parking brake (Step "B").


iii.

With the brake pedal depressed, start the engine (Step "C").


iv.

While holding the brake pedal down, apply the parking brake (Step "D").


v.

With the parking brake applied, depress and release the brake pedal twice (Step "E").


vi.

While holding the brake pedal down, release and apply the parking brake twice (Step "F").


vii.

With the parking brake applied, depress and release the brake pedal twice (Step "G").


viii.

Check that the VSC OFF indicator light comes on and the TRC OFF message is displayed on the multi-information display (Step "H").

NOTICE:

Turn the ignition switch off when 60 seconds or more have elapsed since Inspection Mode was entered. If the ignition switch is turned off before 60 seconds or more elapse, Inspection Mode continues when the ignition switch is turned to ON.


HINT:
·

If the VSC OFF indicator light does not come on and the TRC OFF message is not displayed on the multi-information display in step "H", repeat steps "A" to "H".

·

Turning the ignition switch off ends Inspection Mode.