Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0444806 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.



CHECK FREEZE FRAME DATA WHEN DTC WAS STORED


HINT:
·

Freeze frame data is stored when a DTC is output.

·

Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.



a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3 and turn the ignition switch to ON.


c.

Operate the GTS to enter the Trouble Codes.

Chassis > Brake/EPB > Trouble Codes
50001 435

d.

Select a DTC to display the freeze frame data.


e.

Check the freeze frame data for the output DTC.

Chassis > Brake/EPB
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa
Max.: 23.99 MPa
Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
Master Cylinder Sensor Temperature Master cylinder pressure sensor temperature Min.: -80°C
Max.: 175°C
Displays temperature master cylinder pressure sensor -
M/C Sensor Grade Master cylinder pressure sensor change (value detected by ECU) Min.: -30 MPa/s
Max.: 225 MPa/s
Brake pedal released or pedal held at constant position: 0 MPa/s When brake pedal is being operated: Changes in proportion with the pedal movement speed
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Steering Angle Value Steering sensor Min.: -3276.8°
Max.: 3276.7°
Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0°
-
MT Voltage Value ABS motor drive voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to the ABS motor) from the skid control ECU (brake actuator assembly) to the ABS motor relay


Solenoid Power Supply Voltage Solenoid power supply voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to each solenoid) from the skid control ECU (brake actuator assembly) to the ABS solenoid relay


Engine Revolutions Engine speed Min.: 0 rpm
Max.: 65535 rpm
Engine stopped: 0 rpm When engine speed is constant: No large fluctuations
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%
Max.: 127.5%
Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Real Engine Torque Powertrain drive-torque Min.: -1024.000 Nm
Max.: 1023.000 Nm
- -
Shift Lever Position Shift lever position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input Actual shift lever position -
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) /
Not defined /
VSC OFF mode (TRC(TRAC) OFF/VSC OFF)
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Brake Hold Control Mode Brake hold control mode Out of control mode /
Pressure hold mode /
Pressure release mode /
Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated)
Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated)
Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated)
HINT:
·

EPB stands for electric parking brake

·

If the brake pedal is not depressed for 3 minutes of more after entering pressure hold mode, the system automatically changes to EPB lock mode



FR Target Oil Pressure Front wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
FL Target Oil Pressure Front wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
RR Target Oil Pressure Rear wheel RH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
RL Target Oil Pressure Rear wheel LH target oil pressure Min.: 0.0 MPa
Max.: 20.0 MPa
- Different according to target oil pressure of each wheel
Vehicle Speed Maximum wheel speed sensor reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Grade Vehicle acceleration Min.: -25.105 m/s2
Max.: 24.908 m/s2
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration: 0.000 to 24.908 m/s2
Vehicle Stop Time from IG ON Time vehicle stopped after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Travel Distance from IG ON Driving time after ignition switch turned to ON Min.: 0 s
Max.: 1275 s
- -
Stop Light SW Stop light switch assembly (STP terminal input) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:

The brake pedal state is determined using the voltage at terminal STP


Parking Brake SW Parking brake switch OFF / ON OFF: Parking brake released
ON: Parking brake applied
-
Reverse Position Switch Reverse position switch OFF / ON OFF: Reverse position switch OFF
ON: Reverse position switch ON
-
Brake Hold Switch Brake hold switch (electric parking brake switch assembly) (BH terminal input) OFF / ON OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON
HINT:

The brake hold switch (electric parking brake switch assembly) state is determined using the voltage at terminal BH


Stop Light Relay Stop light switch assembly (STP2 terminal input) OFF / ON OFF: Stop light switch assembly (STP2 terminal input) OFF
ON: Stop light switch assembly (STP2 terminal input) ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Inspection Mode Inspection mode OFF / ON OFF: Normal mode
ON: Inspection mode
HINT:

Refer to utility for details on how to enter inspection mode*1


TRC(TRAC) Control TRC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Engine Control TRC engine control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Brake Control TRC brake control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel ABS Ctrl Status Front wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
BA Ctrl Status BA control status OFF / ON OFF: During not control
ON: During control
-
PBA Ctrl Status PBA control status OFF / ON OFF: During not control
ON: During control
-
Stop Light Relay State for ECU Control Stop light switch assembly (STPO terminal output) (value detected by ECU) OFF / ON OFF: Stop light switch assembly not operating
ON: Stop light switch assembly operating
-
Solenoid State for ECU Control ABS solenoid relay status (for ECU control) OFF / ON OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating
-
Motor State for ECU Control ABS motor relay status (for ECU control) OFF / ON OFF: ABS motor relay not operating
ON: ABS motor relay operating
-
Operation History of IG OFF while Vehicle is moving History of ignition switch turned off when vehicle is in motion OFF / ON OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
-
Buzzer Meter buzzer OFF / ON OFF: Buzzer off
ON: Buzzer on
-
Dealer Mode Dealer Mode (Signal Check mode or Calibration mode) status OFF / ON OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode)
HINT:
·

for details on Dealer Mode (Signal Check), refer to test mode procedure*2

·

for details on Dealer Mode (Calibration), refer to utility*3



Zero Point Memory State of Steering Angle Sensor Steering sensor zero point memorization status Zero point is not memorized / Zero point is memorized -
HINT:

The steering sensor zero point is acquired when the vehicle is being driven in a straight line at a speed of 35 km/h (22 mph) or more for approximately 5 seconds


TRC(TRAC)/VSC OFF SW VSC OFF switch (combination switch assembly) (CSW terminal input) OFF / ON OFF: VSC OFF switch (combination switch assembly) OFF
ON: VSC OFF switch (combination switch assembly) ON
HINT:

The VSC OFF switch (combination switch assembly) state is determined using the voltage at terminal CSW


IGP_PT1 IGP_PT1 status OFF / ON OFF: IGP_PT1 off
ON: IGP_PT1 on
-
FR Wheel Rotatory direction for front wheel RH Forward / Back - -
FL Wheel Rotatory direction for front wheel LH Forward / Back - -
RR Wheel Rotatory direction for rear wheel RH Forward / Back - -
RL Wheel Rotatory direction for rear wheel LH Forward / Back - -
FR Speed Open Front speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
FL Speed Open Front speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
RR Speed Open Rear speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
RL Speed Open Rear speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
EFI Communication Open ECM communication open detection Under intermittent / Normal Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected
-
Yaw Rate Open Yaw rate sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Deceleration Open Acceleration sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Steering Open Steering sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Master Cylinder Open Master cylinder pressure sensor open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
M/C Pressure Sensor Noise Master cylinder pressure sensor noise detection Under intermittent / Normal Under intermittent: Noise detected
Normal: Noise not detected
-
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
EFI Communication Invalid ECM communication invalid detection Under intermittent / Normal Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected
-
Master Cylinder Pressure Sensor Power Supply Open Master cylinder pressure sensor power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Solenoid Power Supply Open Solenoid power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Motor Power Supply Open Motor power supply voltage status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Stop Switch Open Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Air Bag ECU Communication Open Airbag sensor assembly open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
IGR Voltage IGR terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
+BS Voltage +BS terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal +BS (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)


+BM Voltage BM terminal voltage value (value detected by ECU) Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal BM (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)





CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTC will also clear the Freeze Frame Data.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTC and Freeze Frame Data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Chassis > Brake/EPB > Clear DTCs
50002 435