Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0446873 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C052C12  ABS Pump Motor Control Circuit Short to Battery  C052C14  ABS Pump Motor Control Circuit Short to Ground or Open  


DESCRIPTION

The ABS motor relay is built into the brake booster with master cylinder assembly.

During ABS, TRC, VSC, brake hold, secondary collision brake or brake assist operation, the skid control ECU (brake booster with master cylinder assembly) turns on the ABS motor relay to run the pump motor in the brake actuator assembly.

When any DTC related to the ABS motor is stored, the IC built into the skid control ECU (brake booster with master cylinder assembly) operates in fail-safe mode.

When the supplied voltage to the BM terminal of the ABS motor relay is excessively low due to an auxiliary battery or charging circuit malfunction, DTC C052C12 and/or C052C14 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C052C12 ABS Pump Motor Control Circuit Short to Battery A short in the ABS motor relay drive circuit is detected for 4 seconds or more.
·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)

·

Brake actuator assembly


Brake/EPB A
C052C14 ABS Pump Motor Control Circuit Short to Ground or Open When operation of the ABS motor is requested, the ABS motor voltage is less than 7.6 V for 0.2 seconds or more.
·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)

·

Brake actuator assembly


Brake/EPB A

WIRING DIAGRAM

C345758E18
1.74,0.427 2.271,0.771 0.531,0.344 10 false 41 1.979,0.656 2.51,1 0.531,0.344 10 false BM 0.75,0.677 1.906,1.104 1.156,0.427 10 false ABS MTR NO. 3 0.156,2.115 1.542,2.563 1.385,0.448 10 false from Auxiliary Battery 2.104,2.969 2.635,3.313 0.531,0.344 10 false A38 2.104,3.135 4.177,3.563 2.073,0.427 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.177,1.948 2.708,2.292 0.531,0.344 10 false IC 3.042,0.917 3.771,1.375 0.729,0.458 10 false ABS Motor Relay 4.313,1.042 4.844,1.385 0.531,0.344 10 false 40 5.323,1.042 5.854,1.385 0.531,0.344 10 false 10 5.542,2.615 6.073,2.958 0.531,0.344 10 false MGND 5.385,3.156 7.073,3.625 1.688,0.469 10 false Brake Actuator Assembly 3.948,1.24 4.479,1.583 0.531,0.344 10 false +BM 5.531,1.24 6.063,1.583 0.531,0.344 10 false +BM 5.385,2.396 5.917,2.74 0.531,0.344 10 false 1 5.406,2.99 5.938,3.333 0.531,0.344 10 false A95

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
Only C052C12 or C052C14 is output A
None of the above conditions are met B




A

3.CHECK HARNESS AND CONNECTOR (BM TERMINAL)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (BM TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A38)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

A38-41 (BM) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BM CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A95 brake actuator assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A38,A95)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A38-40 (+BM) - A95-10 (+BM) Always Below 1 Ω
A38-40 (+BM) or A95-10 (+BM) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A95)Location & Routing

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A95-1 (MGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

6.CLEAR DTC

Pre-procedure1

a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A95 brake actuator assembly connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C052C12 and C052C14 are not output A
C052C12 or C052C14 is output B


HINT:
·

If a speed signal of 20 km/h (12 mph) or more is sent to the skid control ECU (brake booster with master cylinder assembly) with the ignition switch ON and the stop light switch assembly off, the ECU performs self-diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake booster with master cylinder assembly).

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake booster with master cylinder assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY