| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.
This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.
Be sure to wear insulating gloves when working on high voltage wiring or components.
If work is performed without wearing insulating gloves, there is a danger of electric shock.
While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
2.REMOVE WINDSHIELD WIPER MOTOR AND LINK
55815E
3.REMOVE FRONT NO. 1 VENTILATOR SEAL
55735A
4.REMOVE WATER GUARD PLATE LH
55701J
5.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
6.PERFORM ACCUMULATOR PRESSURE ZERO DOWN
Using the GTS, perform the accumulator pressure zero down.
1. Connect the GTS to the DLC3 with the ignition switch off.
2. Turn the ignition switch to ON.
3. Turn the GTS on and enter the following menus: Chassis / Brake / Utility / ECB (Electronically Controlled Brake system) Utility.
| Tester Display |
|---|
| ECB Utility |
4. Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.
5. Perform "Motor Invalid" according to the display on the GTS.
6. Enter the following menus: Chassis / Brake / Utility / ECB (Electronically Controlled Brake system) Utility.
| Tester Display |
|---|
| ECB Utility |
7. Select "ECB (Electronically Controlled Brake system) Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.
8. Perform "ECB (Electronically Controlled Brake system) Invalid" according to the display on the GTS.
9. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.
10. Check that the brake pedal is firm.
If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down is not complete.
11. Turn the GTS off and turn the ignition switch off.
12. Disconnect the GTS from the DLC3.
13. Disconnect the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
When the accumulator pressure zero down could not be performed using the GTS:
|
Release the lock lever |
|
Disconnect the connector |
If DTCs are output, accumulator pressure zero down may not be complete. In this case, perform the following procedure.
1. With the ignition switch off, release the lock lever and disconnect the brake booster pump assembly connector as shown in the illustration.
2. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
3. Check that the brake pedal is firm.
If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down is not complete.
4. Disconnect the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
7.DRAIN BRAKE FLUID
|
|
82111
8.REMOVE ENGINE ROOM MAIN WIRE
| *a | Lock Lever | *b | Lock Arm |
| *c | Push | *d | Screwdriver Insertion Point |
| *e | Pre-lock | - | - |
|
Release the lock lever |
|
Disconnect the connector |
Disconnect the connector from the brake booster with master cylinder assembly.
Disengage the clamp.
Push the lock arm of the connector to release the lock and rotate the lock lever to the position shown in the illustration.
Using a screwdriver, release the pre-lock and disconnect the connector from the brake booster with master cylinder assembly as shown in the illustration.
Disengage the clamp to separate the engine room main wire.
44572C
9.DISCONNECT NO. 2 BRAKE ACTUATOR HOSE
47374B
10.REMOVE NO. 4 BRAKE TUBE CLAMP
11.DISCONNECT BRAKE LINE
Using a union nut wrench, disconnect the 3 brake lines from the brake booster with master cylinder assembly.
Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
87211
12.REMOVE NO. 1 AIR DUCT
47101A
13.REMOVE BRAKE PEDAL RETURN SPRING
47264A
14.REMOVE PUSH ROD PIN
47210L
15.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Remove the 4 nuts and brake booster with master cylinder assembly.
| *1 | Skid Control ECU |
| *2 | No. 1 Reservoir Hose |
| *3 | Brake Master Cylinder Push Rod Clevis |
| *4 | Boot |
| *5 | Master Cylinder Reservoir Assembly |
| *6 | Brake Actuator Bracket |
Do not kink or damage the brake lines.
Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.
Be careful not to allow any brake fluid to enter the connector.
44785
16.REMOVE BRAKE BOOSTER GASKET