Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0446873 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C120200  Master Reservoir Level Malfunction  


DESCRIPTION

If the skid control ECU (brake booster with master cylinder assembly) detects that the brake fluid level is low or there is an open in the brake fluid level warning switch signal circuit, DTC C120200 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C120200 Master Reservoir Level Malfunction
·

The brake fluid level warning switch signal circuit is open for a certain period of time.

·

The reservoir level is low for a certain period of time.


·

Open or short in brake fluid level warning switch (brake booster with master cylinder assembly)

·

Brake fluid leaks

·

Open or short in wire harness

·

Low brake fluid

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A

WIRING DIAGRAM

C345753E34
5,1.229 5.313,1.427 0.313,0.198 10 false 16 5.26,1.229 5.573,1.427 0.313,0.198 10 false LBL 4.927,2.958 5.24,3.156 0.313,0.198 10 false A38 4.917,3.146 6.979,3.521 2.063,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.01,1.229 4.323,1.427 0.313,0.198 10 false 1 3.708,1.229 4.021,1.427 0.313,0.198 10 false + 2.417,1.229 2.729,1.427 0.313,0.198 10 false E 2.063,1.229 2.375,1.427 0.313,0.198 10 false 2 1.927,2.104 2.24,2.302 0.313,0.198 10 false A24 1.917,2.271 4.417,2.656 2.5,0.385 10 false Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly) 6.26,1.354 6.573,1.552 0.313,0.198 10 false IC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only C120200 is output A
C120200 and other DTCs are output B



A

2.CHECK VEHICLE TYPE

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK VEHICLE TYPE
a.

Check the vehicle specification.


Result:
Result Proceed to
for AWD A
for 2WD B



A

3.CHECK BRAKE FLUID LEVEL

B

4.CHECK BRAKE FLUID LEVEL
3.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is sufficient.

HINT:

If the fluid level is low, check for fluid leaks, and repair as necessary.


i.

Check for brake fluid leaks (connection between the brake booster pump assembly, brake master cylinder reservoir assembly (brake booster with master cylinder assembly), brake booster with master cylinder assembly, and wheel cylinders).

If no leaks exist, add and adjust fluid using the GTS.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>ON-VEHICLE INSPECTION


ii.

Check the thickness of the brake pad lining.

for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE (for AWD)>INSPECTION

HINT:

If the thickness is less than the standard, replace the brake pads with new ones.




Result:
Proceed to
NEXT



NEXT

5.CHECK FOR FLUID LEAK
4.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is sufficient.

HINT:

If the fluid level is low, check for fluid leaks, and repair as necessary.


i.

Check for brake fluid leaks (connection between the brake booster pump assembly, brake master cylinder reservoir assembly (brake booster with master cylinder assembly), brake booster with master cylinder assembly, and wheel cylinders).

If no leaks exist, add and adjust fluid using the GTS.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>ON-VEHICLE INSPECTION


ii.

Check the thickness of the brake pad lining.

for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE (for 2WD)>INSPECTION

HINT:

If the thickness is less than the standard, replace the brake pads with new ones.




Result:
Proceed to
NEXT



NEXT

5.CHECK FOR FLUID LEAK
5.CHECK FOR FLUID LEAK
a.

Check that there are no leaks from the connections between the brake booster pump assembly and brake booster with master cylinder assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

Bleed the air from the brake system.

HINT:

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING



ii.

Turn the ignition switch off.


iii.

Disconnect the A27 brake pedal stroke sensor assembly connector.


iv.

Select the Data List on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
MTT Pump motor operation status OFF / ON OFF: Pump motor off
ON: Pump motor on
-
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 15.00 to 21.00 MPa
(Pressure stable and pump motor stopped)
When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > Brake/EPB > Data List
Tester Display
MTT
Accumulator Pressure
50003 435 100,212

v.

Depress the brake pedal several times to operate the pump motor, then wait until it stops.


vi.

After the pump motor stops, wait for 30 seconds, then check the drop in the accumulator pressure sensor output value and the state of the pump motor.



Result:
Result Proceed to
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure after the pump motor stops is less than 2.50 MPa and pump motor does not operate within 30 seconds A
30 seconds after the pump motor stops the drop in the value of Accumulator Pressure is 2.50 MPa or more or pump motor operates within 30 seconds B



A

6.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)

B

CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID

6.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A27 brake pedal stroke sensor assembly connector.


c.

Remove the brake master cylinder reservoir filler cap assembly.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A24 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.
C230719C58
0.917,2.958 1.5,1.99 true 2.365,3 1.938,1.99 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 0.792,2.969 1.104,3.167 0.313,0.198 10 false E 2.385,2.979 2.698,3.177 0.313,0.198 10 false +
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Booster with Master Cylinder Assembly))


Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the brake master cylinder reservoir assembly (brake booster with master cylinder assembly). Its position changes according to the level of brake fluid.


Standard Resistance:
Tester Connection Condition Specified Condition
2 (E) - 1 (+) Brake fluid level warning switch (brake booster with master cylinder assembly) off (float up) 1.84 to 2.16 kΩ
2 (E) - 1 (+) Brake fluid level warning switch (brake booster with master cylinder assembly) on (float down) Below 1 Ω


HINT:

If there are no problems after completing the preceding inspection, adjust the brake fluid to the MAX level with the ignition switch ON.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A38,A24)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

Click Connector(A24)Engine Compartment>Engine Room Main Wire>Level Warning Switch (Brake Master Cylinder Reservoir Assembly)

A38-16 (LBL) - A24-1 (+) Always Below 1 Ω
A38-16 (LBL) or A24-1 (+) - Body ground Always 10 kΩ or higher
A24-2 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SWITCH INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SWITCH INPUT)

Pre-procedure1

a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A24)Location & Routing

Click Connector(A24)Engine Compartment>Engine Room Main Wire>Level Warning Switch (Brake Master Cylinder Reservoir Assembly)

A24-1 (+) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

9.CLEAR DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the A24 brake fluid level warning switch (brake booster with master cylinder assembly) connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C120200 is not output A
C120200 is output B



Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY