Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0446873 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C12F812  ECB Solenoid Control "A" Circuit Short to Battery  C12F814  ECB Solenoid Control "A" Circuit Short to Ground or Open  


DESCRIPTION

The main relay supplies power to the switching solenoid and the linear solenoid.

The main relay remains on for approximately 3 minutes after the ignition switch is turned off and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C12F812 ECB Solenoid Control "A" Circuit Short to Battery The BS terminal voltage is 3.5 V or more for 4.5 seconds or more, when operation of the main relay is requested.
·

Short in main relay circuit

·

Main relay internal stuck

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A
C12F814 ECB Solenoid Control "A" Circuit Short to Ground or Open
·

When the ignition switch ON (READY):

The BS terminal voltage is less than 3.5 V for 0.05 seconds or more, when the IGR terminal voltage is 9.5 V or more and operation of the main relay is requested.

·

When the ignition switch is off:

The BS terminal voltage is less than 3.5 V for 0.05 seconds or more, when operation of the main relay is requested.


·

Open or short in main relay circuit

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ECB MAIN RELAY)
a.

Select the Active Test on the GTS.

Chassis > Brake/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ECB Main Relay Main relay Relay ON/OFF ECB: Electronically Controlled Brake System
Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECB Main Relay Main relay operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
Chassis > Brake/EPB > Active Test
Active Test Display
ECB Main Relay
Data List Display
ECB Main Relay
50004 435 41 266

b.

Check that the condition of the ECB main relay observed on the GTS changes according to GTS operation.


Result:
Result Proceed to
ECB main relay in the Data List turns ON/OFF using the Active Test. A
ECB main relay in the Data List does not change using the Active Test. B



A

2.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

B

5.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
2.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure2

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A38)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

A38-52 (BS) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)

3.CLEAR DTC

Pre-procedure1

a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
C12F812 and C12F814 are not output A
C12F812 or C12F814 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (+BI TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A38)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

A38-15 (+BI1) - Body ground Always 11 to 14 V
A38-5 (+BI2) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BI CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (BS TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A38)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

A38-52 (BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)