The skid control ECU (brake booster with master cylinder assembly) stores the individual characteristic of each holding solenoid built into the brake actuator assembly. Based on the stored information, the skid control ECU (brake booster with master cylinder assembly) calibrates the individual differences and controls systems.
The skid control ECU (brake booster with master cylinder assembly) receives the park (P) signal from the hybrid vehicle control ECU through the CAN communication system.
These DTCs are cleared when the ABS holding solenoid valve learning results are normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C134951 | Pressure Holding Solenoid Valve Learning Not Programmed | The ABS holding solenoid valve learning value is not stored. | Perform ABS holding solenoid valve learning and check for DTCs. If no DTCs are output again, the valve is normal. | Brake/EPB | A |
| C134954 | Pressure Holding Solenoid Valve Learning Missing Calibration | The ABS holding solenoid valve learning value cannot be obtained. | ·
Perform ABS holding solenoid valve learning and check for DTCs. If no DTCs are output again, the valve is normal. ·
Skid control ECU (brake booster with master cylinder assembly) ·
Brake actuator assembly |
Brake/EPB | A |
After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Before performing linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization, DTC C124A00 will be output.
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Check that DTCs other than C134951 and C134954 are not output.
| Result | Proceed to |
|---|---|
| Only C134951 or C134954 is output | A |
| None of the above conditions are met | B |
A
B
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Check and ensure the following conditions required for performing ABS holding solenoid valve learning and then perform ABS holding solenoid valve learning.
| Tester Display |
|---|
| ECB Utility |
The auxiliary battery voltage is 11 to 15.5 V when the ignition switch ON (READY).
The brake actuator assembly is not hot.
The hybrid control system is not malfunctioning.
The shift state indicator shows that the vehicle shift state is park (P).
The READY light in the combination meter assembly is illuminated.
The brake pedal is not depressed.
The parking brake is released.
Learning will be performed in the order of linear solenoid valve offset learning and then ABS holding solenoid valve learning.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C134951 and C134954 are not output | A |
| C134951 or C134954 is output | B |
Post-procedure1
None
A
B
Select the Active Test on the GTS.
| Tester Display | Measurement Item | Control Range | Restrict Condition | Diagnostic Note |
|---|---|---|---|---|
| ABS Solenoid | Pressure holding solenoid (SFRH, SFLH, SRRH, SRLH)
Pressure reduction solenoid (SFRR, SFLR, SRRR, SRLR) |
Solenoid Start (Activate)
Solenoid SFRH / SFLH / SRRH / SRLH / SFRR / SFLR / SRRR / SRLR |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P or N ·
Apply the parking brake
|
Check that the GTS display for the solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR or SFRH) changes to ON/OFF during Solenoid Start (Activate) |
| Tester Display |
|---|
| ABS Solenoid |
Operate the SFRH (front right wheel holding solenoid valve), SFLH (front left wheel holding solenoid valve), SRRH (rear right wheel holding solenoid valve) and SRLH (rear left wheel holding solenoid valve) solenoids one by one. While operating each solenoid, depress the brake pedal, open the corresponding bleeder plug and check that brake fluid does not flow from the bleeder plug.
Brake fluid does not flow from the corresponding bleeder plug when the brake pedal is depressed when operating each solenoid.
While not operating the SFRH (front right wheel holding solenoid valve), SFLH (front left wheel holding solenoid valve), SRRH (rear right wheel holding solenoid valve) and SRLH (rear left wheel holding solenoid valve) solenoids, depress the brake pedal, open each bleeder plug and check that brake fluid flows from each bleeder plug.
Brake fluid flows from each bleeder plug when not operating each solenoid and the brake pedal is depressed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG