Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › 2020.08–2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0446873 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  P05FF62  Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure  


DESCRIPTION

If the skid control ECU (brake booster with master cylinder assembly) detects an inconsistency between the brake pedal stroke sensor assembly signal and reaction force pressure sensor signal, DTC P05FF62 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
P05FF62 Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure The difference between brake pedal stroke sensor assembly output value and reaction force pressure sensor output value is above the threshold for a certain period of time.
·

Brake actuator (brake booster with master cylinder assembly)

·

Brake pedal stroke sensor assembly


Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake actuator (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA
a.

Interview the customer to check the vehicle conditions when the brake system warning light (red indicator) and brake system warning light (yellow indicator) illuminated.


b.

Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.

Chassis > Brake/EPB > Trouble Codes
50001 435

HINT:
·

Freeze Frame Data is only stored once when a DTC is stored.

·

If other DTCs are output, repair any malfunctions related to those DTCs first, and then reproduce the conditions that caused DTC P05FF62 to be stored based on the interview with the customer.



Result:
Proceed to
NEXT



NEXT

2.INSPECT BRAKE PEDAL STROKE SENSOR ASSEMBLY OUTPUT VOLTAGES AND WHEEL CYLINDER PRESSURE (STROKE SENSOR, STROKE SENSOR2)
2.INSPECT BRAKE PEDAL STROKE SENSOR ASSEMBLY OUTPUT VOLTAGES AND WHEEL CYLINDER PRESSURE (STROKE SENSOR, STROKE SENSOR2)
a.

Turn the ignition switch off.


b.

Mount a pedal effort gauge.


c.

Disconnect the A12 brake booster pump assembly connector.


d.

Depress the brake pedal 10 times or more until it becomes hard.

HINT:

Depressing the brake pedal with the connector of the brake booster pump assembly disconnected drops the accumulator pressure to approximately 0 MPa.



e.

Connect an LSPV gauge set.


f.

Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor 1 Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor 2 Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Chassis > Brake/EPB > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 435 207,208
NOTICE:

Check the wheel cylinder pressure with the switching solenoid (SSA, SGH) off and an accumulator pressure of 0 MPa.


Standard Result:
Front
Pedal Effort
(N (kgf, lbf))
Stroke Sensor
(V)
Stroke Sensor 2
(V)
Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
200 (20, 45.0) 1.23 to 1.93 3.07 to 3.77 0.06 to 2.06 (0.6 to 21.0, 9 to 299)
500 (51, 112.4) 1.42 to 2.12 2.88 to 3.58 2.09 to 4.09 (21.3 to 41.7, 303 to 593)

Rear
Pedal Effort
(N (kgf, lbf))
Stroke Sensor
(V)
Stroke Sensor 2
(V)
Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
200 (20, 45.0) 1.23 to 1.93 3.07 to 3.77 0.06 to 2.06 (0.6 to 21.0, 9 to 299)
500 (51, 112.4) 1.42 to 2.12 2.88 to 3.58 2.09 to 4.09 (21.3 to 41.7, 303 to 593)



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

3.REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY
3.REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Reconnect the A30 brake booster pump assembly connector.


c.

Replace brake pedal stroke sensor assembly.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR>REMOVAL



d.

Perform zero point calibration of the brake pedal stroke sensor assembly.


Chassis > Brake/EPB > Utility
Tester Display
Reset Memory
50005 435 4560
Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554
Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
P05FF62 is not output A
P05FF62 is output B



Post-procedure1

a.

None



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY