This DTC is stored when the blind spot monitor sensor LH (B) detects a short to ground in the outer rear view mirror indicator LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1AB411 | Outer Mirror Indicator (Module "B" Side) Circuit Short to Ground | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time |
·
Outer mirror LH (outer rear view mirror indicator LH) ·
Outer rear view mirror assembly LH ·
Harness or connector ·
Blind spot monitor sensor LH (B) |
Blind Spot Monitor "B" | A |
w/ Panoramic View Monitor System
w/o Panoramic View Monitor System
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Turn the ignition switch off.
Turn the ignition switch to ON.
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| w/ Panoramic View Monitor System | A |
| w/o Panoramic View Monitor System | B |
A
B
Pre-procedure1
Disconnect the T6 blind spot monitor sensor LH (B) connector.
Disconnect the L8 outer rear view mirror assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(T6)Location & Routingewd_type=routing;type=c;code=T6 Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LHewd_type=component;type=c;code=T6;pinno=4 |
||
| T6-4 (OMIL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B outer mirror LH (outer rear view mirror indicator LH) connector.
Procedure1
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L8)Location & Routingewd_type=routing;type=c;code=L8 Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LHewd_type=component;type=c;code=L8;pinno=8 |
||
| L8-8 (BSL+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the T6 blind spot monitor sensor LH (B) connector.
Disconnect the L12 outer rear view mirror assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(T6)Location & Routingewd_type=routing;type=c;code=T6 Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LHewd_type=component;type=c;code=T6;pinno=4 |
||
| T6-4 (OMIL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the D outer mirror LH (outer rear view mirror indicator LH) connector.
Procedure1
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L12)Location & Routingewd_type=routing;type=c;code=L12 Click Connector(L12)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LHewd_type=component;type=c;code=L12;pinno=1 |
||
| L12-1 (BSL+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG