This DTC is stored when the blind spot monitor sensor LH (B) detects a short to +B in the outer rear view mirror indicator LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1AB412 | Outer Mirror Indicator (Module "B" Side) Circuit Short to Battery | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time |
·
Outer mirror LH (outer rear view mirror indicator LH) ·
Outer rear view mirror assembly LH ·
Harness or connector ·
Blind spot monitor sensor LH (B) |
Blind Spot Monitor "B" | A |
w/ Panoramic View Monitor System
w/o Panoramic View Monitor System
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Turn the ignition switch off.
Turn the ignition switch to ON.
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| w/ Panoramic View Monitor System | A |
| w/o Panoramic View Monitor System | B |
A
B
Pre-procedure1
Disconnect the T6 blind spot monitor sensor LH (B) connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(T6)Location & Routingewd_type=routing;type=c;code=T6 Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LHewd_type=component;type=c;code=T6;pinno=4 |
||
| T6-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the B outer mirror LH (outer rear view mirror indicator LH) connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(T6)Location & Routingewd_type=routing;type=c;code=T6 Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LHewd_type=component;type=c;code=T6;pinno=4 |
||
| T6-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the L8 outer rear view mirror assembly LH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(T6)Location & Routingewd_type=routing;type=c;code=T6 Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LHewd_type=component;type=c;code=T6;pinno=4 |
||
| T6-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the T6 blind spot monitor sensor LH (B) connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(T6)Location & Routingewd_type=routing;type=c;code=T6 Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LHewd_type=component;type=c;code=T6;pinno=4 |
||
| T6-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the D outer mirror LH (outer rear view mirror indicator LH) connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(T6)Location & Routingewd_type=routing;type=c;code=T6 Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LHewd_type=component;type=c;code=T6;pinno=4 |
||
| T6-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the L12 outer rear view mirror assembly LH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(T6)Location & Routingewd_type=routing;type=c;code=T6 Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LHewd_type=component;type=c;code=T6;pinno=4 |
||
| T6-4 (OMIL) - Body ground | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG