Home › General › MAINTENANCE › REAR BRAKE FLEXIBLE HOSE (for AWD) › 2020.08–2021.07
RM3700E _V1 General _093024 MAINTENANCE _0447176 REAR BRAKE FLEXIBLE HOSE(for AWD) A

MAINTENANCE  REAR BRAKE FLEXIBLE HOSE(for AWD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C445706N06
5.448,1.833 6.281,2.01 0.833,0.177 5.406,1.792 6.313,2.052 0.906,0.26 3.667,0.083 4.521,0.417 0.854,0.333 3.625,0.042 4.573,0.469 0.948,0.427 6.333,1.083 6.667,1.083 false 6.333,0.698 6.667,0.698 false 6.333,0.292 6.667,0.292 false 3.938,3.958 4.271,3.958 false 4.083,2.708 3.917,2.708 3.917,2.708 3.427,2.188 true 4.521,1.115 4.854,1.115 false 4.313,0.615 4.646,0.615 false 4.833,1.906 5.167,1.906 false 2.573,1.323 3.5,0.25 3.5,0.25 3.667,0.25 true 5.531,0.156 5.813,0.51 0.281,0.354 18 false 2 5.708,0.219 6.063,0.573 0.354,0.354 12 false (*A) 5.833,0.583 6.115,0.938 0.281,0.354 18 false 6 3.771,3.833 4.052,4.188 0.281,0.354 18 false 5 6.146,0.958 6.385,1.281 0.24,0.323 18 false 3 4.417,2.604 4.698,2.958 0.281,0.354 18 false 1 4.938,1.073 5.292,1.427 0.354,0.354 10 false ● 6.01,0.646 6.365,1 0.354,0.354 12 false (*A) 4.708,0.563 5.063,0.917 0.354,0.354 10 false ● 5.229,1.813 5.583,2.167 0.354,0.354 10 false ● 5.531,1.865 7.063,2.063 1.531,0.198 8 false 30.4 (310, 22) 3.719,0.125 5.25,0.323 1.531,0.198 8 false 15.2 (155, 11) 3.719,0.271 5.25,0.469 1.531,0.198 8 false 13.4 (137, 10)* 6.021,0.167 6.469,0.542 0.448,0.375 18 false , 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR FLEXIBLE HOSE 47319F (Click here) - -
2 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 ADD BRAKE FLUID - - (Click here) -
4 BLEED BRAKE LINE - (Click here) (Click here) -
5 REAR WHEEL - - - -
6 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

*A for HV Model - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) * For use with a union nut wrench
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

Because the left and right rear flexible hoses are not interchangeable, verify the part number when installing the rear flexible hoses.

·

When reusing the rear flexible hoses, use the identification marks created during removal to install each rear flexible hose to its original position.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47319F 1.INSTALL REAR FLEXIBLE HOSE

Z101186

NOTICE:

When installing the rear flexible hose, minimize twisting of the hose.



a.
C445715C03
2.073,1.177 2.385,1.375 0.313,0.198 10 false *a 0.583,0.063 1.417,0.396 0.833,0.333 18 false i, ii, iii
*a Torque Wrench Fulcrum Length - -


i.

Install the rear flexible hose with a new clip.

NOTICE:

Install the clip as far as it will go.



ii.

Using a union nut wrench, connect the brake line to the rear flexible hose while holding the rear flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




iii.

Install the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.




Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

Z101186

Click here(Click here)

Hide 5.INSTALL REAR WHEEL

Hide 6. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HV Model)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART