When the brake pedal is depressed, the stop light switch assembly outputs a signal to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the hybrid vehicle control ECU determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| P057162 | Brake Switch "A" Signal Compare Failure | When the ignition switch is ON and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more. | ·
Harness or connector ·
Stop light switch assembly ·
Hybrid vehicle control ECU |
Radar Cruise1 | A |
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.
Pre-procedure1
Disconnect the A63 stop light switch assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63)Location & Routingewd_type=routing;type=c;code=A63 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=2 |
||
| A63-2 (GND) - Body ground | Always | Below 1 Ω |
Procedure2
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A63)Location & Routingewd_type=routing;type=c;code=A63 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=7,6 |
||
| A63-7 (B) - Body ground | Always | 11 to 14 V |
| A63-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| A63-6 (B) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the A63 stop light switch assembly connector.
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| w/ Entry and Start System | A |
| w/o Entry and Start System | B |
A
B
Pre-procedure1
Disconnect the A68 hybrid vehicle control ECU connectors.
Disconnect the A63 stop light switch assembly connector.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the H45 certification ECU (smart key ECU assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A68,A63)Location & Routingewd_type=routing;type=c,c;code=A68,A63 Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=A68;pinno=5,6 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=5,3 |
||
| A68-5 (ST1-) - A63-5 (L) | Always | Below 1 Ω |
| A68-6 (STP) - A63-3 (L) | Always | Below 1 Ω |
| A68-5 (ST1-) or A63-5 (L) - Body ground | Always | 10 kΩ or higher |
| A68-6 (STP) or A63-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the H45 certification ECU (smart key ECU assembly) connector.
Connect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Connect the A63 stop light switch assembly connector.
Connect the A68 hybrid vehicle control ECU connectors.
OK
NG
Pre-procedure1
Disconnect the A68 hybrid vehicle control ECU connectors.
Disconnect the A63 stop light switch assembly connector.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A68,A63)Location & Routingewd_type=routing;type=c,c;code=A68,A63 Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=A68;pinno=5,6 Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=A63;pinno=5,3 |
||
| A68-5 (ST1-) - A63-5 (L) | Always | Below 1 Ω |
| A68-6 (STP) - A63-3 (L) | Always | Below 1 Ω |
| A68-5 (ST1-) or A63-5 (L) - Body ground | Always | 10 kΩ or higher |
| A68-6 (STP) or A63-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Connect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Connect the A63 stop light switch assembly connector.
Connect the A68 hybrid vehicle control ECU connectors.
OK
NG