Home › Power Source / Network › M15A-FKS (BATTERY / CHARGING) › GENERATOR (for 100A Type) › 2020.08–2021.07
RM3700E _57 Power Source / Network _092979 M15A-FKS BATTERY / CHARGING _0438222 GENERATOR(for 100A Type) A

M15A-FKS BATTERY / CHARGING  GENERATOR(for 100A Type)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A478821N01
6.531,0.573 6.865,0.573 false 4.542,1.063 4.875,1.063 false 2.24,2.719 2.573,2.719 false 2.094,1.656 2.427,1.656 false 0.99,1.917 1.323,1.917 false 6.5,0.24 6.833,0.24 false 6.313,0.448 6.594,0.802 0.281,0.354 18 false 1 4.958,0.938 5.24,1.292 0.281,0.354 18 false 3 2.521,1.521 2.802,1.875 0.281,0.354 18 false 4 1.375,2.813 1.656,3.167 0.281,0.354 10 false x2 6.292,0.104 6.573,0.458 0.281,0.354 18 false 2 2.656,2.563 2.938,2.917 0.281,0.354 18 false 4 0.802,1.76 1.083,2.115 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 V-RIBBED BELT 16361A - - -
4 GENERATOR WITH REGULATOR ASSEMBLY 27020 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the generator with regulator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 16361A 3.REMOVE V-RIBBED BELT

Hide 27020 4.REMOVE GENERATOR WITH REGULATOR ASSEMBLY

a.
A459819


b.
A459820