Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT (for 2WD) › from 2021.07
RM3700E _53 Suspension _093738 ALIGNMENT / HANDLING DIAGNOSIS _0441851 REAR WHEEL ALIGNMENT(for 2WD) G

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT(for 2WD)  INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the rear wheel alignment procedure are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Rear wheel alignment adjustment for HV Model TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, ABS holding solenoid valve learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for HV Model TMMF Made:
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)

PROCEDURE

Hide 3.INSPECT CAMBER

NOTICE:

Inspect while the vehicle is unloaded.


a.
C107736C10
2.052,1.26 2.375,1.26 false 2.406,1.167 2.656,1.385 0.25,0.219 10 *a
*a Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Camber Inclination Right-left Difference
M15A-FKS 205/65R16
215/50R18
-1°02' +/- 0°30' (-1.03° +/- 0.50°) 0°33' (0.55°) or less
M15A-FXE 205/65R16
215/50R18
-1°03' +/- 0°30' (-1.05° +/- 0.50°)


Camber (Unloaded Vehicle) (for TMMF Made):
Engine Tire Size Camber Inclination Right-left Difference
M15A-FKS
M15A-FXE
205/65R16
215/55R17
215/50R18
-1°03' +/- 0°30' (-1.05° +/- 0.50°) 0°33' (0.55°) or less


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.



Hide 4.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N (for CVT, Hybrid Transaxle).


c.

Release the parking brake and move the shift lever to neutral (for Manual Transaxle).


d.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


e.
C188968C02
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


f.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.



g.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle) (for TMC Made):
Engine Tire Size Specified Condition
M15A-FKS 205/65R16
215/50R18
C + D: 0°14' +/- 0°17' (0.23° +/- 0.28°)
B - A: 2.9 +/- 3.4 mm (0.114 +/- 0.134 in.)
M15A-FXE 205/65R16
215/50R18
C + D: 0°15' +/- 0°17' (0.25° +/- 0.28°)
B - A: 3.0 +/- 3.4 mm (0.118 +/- 0.134 in.)


Toe-in (Unloaded Vehicle) (for TMMF Made):
Engine Tire Size Specified Condition
M15A-FKS 205/65R16
215/55R17
215/50R18
C + D: 0°15' +/- 0°17' (0.25° +/- 0.28°)
B - A: 2.9 +/- 3.4 mm (0.114 +/- 0.134 in.)
M15A-FXE 205/65R16
215/55R17
215/50R18
C + D: 0°15' +/- 0°17' (0.25° +/- 0.28°)
B - A: 3.0 +/- 3.4 mm (0.118 +/- 0.134 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.


Hide 5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.INSPECT AND ADJUST HEADLIGHT AIMING

HINT:

These procedures are to be performed when suspension or tires components have been removed or replaced.


HINT: