Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM › from 2021.07
RM3700E _53 Suspension _093744 TIRE / WHEEL _0441939 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Inspect the tires for wear and proper inflation pressure.

Cold Tire Inflation Pressure:
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
205/65R16 95H 230 (2.3, 33) 220 (2.2, 32)
215/55R17 94V 220 (2.2, 32) 200 (2.0, 29)
215/50R18 92V 220 (2.2, 32) 200 (2.0, 29)


Cold Tire Inflation Pressure (for Spare Tire):
Tire Size kPa (kgf/cm2, psi)
T145/90D16 106M 420 (4.2, 60)



ii.

Tire pressure adjustment method when warm:

1.

Adjust the tire pressure so that the displayed value is equal to the set pressure.

2.

Perform initialization and check that initialization completes.

HINT:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION


3.

Check and record the value of the Data List item "Temperature in Tire". (Ts)

4.

Check and record the ambient temperature during tire pressure adjustment. (Tm)

5.

Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)

HINT:

Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P

P = (Specified Pressure) + (Ts - Tm)


6.

Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".


Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Temperature in Tire
ID 2 Temperature in Tire
ID 3 Temperature in Tire
ID 4 Temperature in Tire
ID 5 Temperature in Tire
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 452 5,6,7,8,9,10,11,12,13,14


b.
C137874

Using a dial indicator, check the runout of the tires.

Maximum Tire Runout:

1.4 mm (0.0551 in.)



Hide 2. ROTATE TIRES

a.

Remove the wheel assembly.

HINT:

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>REMOVAL



b.
C163156C22
0,0 0,0 false
V100135

Front


Rotate the tires as shown in the illustration.


c.

Install the wheel assembly.

HINT:

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>INSTALLATION




Hide 3.INSPECT AND ADJUST WHEEL BALANCE

a.

Inspect and adjust the off-the-car balance.

i.

for Steel Wheel:

Maximum Wheel Imbalance:

8.0 g (0.0176 lb)


HINT:
·

Use clip-on type balance weights for both the inner and outer side.

·

If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.




ii.
C144018C01
2.052,3.667 2.281,3.823 0.229,0.156 10 false *a
*a 25 mm (0.984 in.)


for Alloy Wheel:

Maximum Wheel Imbalance:

8.0 g (0.0176 lb)


NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the adhesive surface of the balance weight.

·

Adhere a stick-on type balance weight to the flat surface *a shown in the illustration.

·

Push the balance weight with your finger to securely adhere it to the desired position.

·

Do not reuse balance weights.

·

Use only TOYOTA genuine stick-on type balance weights or equivalent.



HINT:
·

Use clip-on type balance weights for the inner side, and stick-on type balance weights for the outer side.

·

If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.