Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for RHD) › from 2021.07
RM3700E _52 Drivetrain _104786 CLUTCH _0480192 CLUTCH PEDAL(for RHD) G

CLUTCH  CLUTCH PEDAL(for RHD)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT CLUTCH PEDAL HEIGHT

a.

Remove the front door scuff plate RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL



b.

Remove the cowl side trim board RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL



c.

Turn back the front floor carpet assembly.


d.

Turn back the dash panel insulator assembly.


e.

Check that the clutch pedal height is correct.

C459818C01
0.896,1.521 1.104,1.719 0.208,0.198 10 true *a 5.781,1.729 6.052,1.948 0.271,0.219 10 true *a
*a Clutch Pedal Height - -
V100155

Measuring Plane of Floor Panel - -


Pedal Height from Floor Panel:
Specified Condition
158.1 to 178.1 mm
6.22 to 7.01 in.



f.

If the result is not as specified, bleed the clutch line and perform the inspection again.


g.

If the result is not as specified after bleeding the clutch line, replace the clutch master cylinder assembly.


h.

Install the dash panel insulator assembly.


i.

Install the front floor carpet assembly.


j.

Install the cowl side trim board RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION



k.

Install the front door scuff plate RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION



Hide 2.INSPECT CLUTCH PEDAL FREE PLAY

a.
C448877C02
2.833,3.146 3.146,3.344 0.313,0.198 10 false *a
*a Clutch Pedal Free Play


Check that the clutch pedal free play is correct.

HINT:

Pay close attention to the change in resistance to distinguish clutch pedal free play while performing the inspection.


i.

Depress the clutch pedal until clutch resistance begins to be felt.

Clutch Pedal Free Play:
Reference:
Specified Condition
3 to 15 mm
0.118 to 0.591 in.



ii.

If the result is not as specified, bleed the clutch line and perform the inspection again.


iii.

If the result is not as specified after bleeding the clutch line, replace the clutch master cylinder assembly.



Hide 3.INSPECT CLUTCH RELEASE POINT

CAUTION:

When checking the clutch release point, ensure that the vehicle is secure.


a.
C227877C12
1.365,1.177 1.615,1.177 false 1.615,1.583 2.281,1.042 2.281,1.042 2.396,1.042 true 1.354,1.521 0.906,1.885 0.906,1.885 0.802,1.885 true 1.396,0.969 1.635,1.177 0.24,0.208 10 false *c 1.792,1.885 2.052,2.094 0.26,0.208 10 false *d 0.646,1.802 0.948,2.052 0.302,0.25 10 false *b 2.458,0.969 2.719,1.198 0.26,0.229 10 false *a
*a Release Point
*b Full Stroke End Position
*c Release Point to Full Stroke End Position
*d Clutch Pedal Stroke


Check the clutch release point.

i.

Be sure to apply the parking brake and secure the wheels using wheel chocks.


ii.

Start the engine and run it at idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever to reverse until the gears contact.


iv.

Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Release Point to Full Stroke End Position:
Specified Condition
25 mm
0.984 in.


Clutch Pedal Stroke at 200 N (20 kgf, 45.0 lbf):
Reference:
Specified Condition
141 to 151 mm
5.55 to 5.94 in.



v.

If the result is not as specified, perform the following procedure.

1.

Check the clutch pedal height.

2.

Check the clutch pedal free play.

3.

Bleed the clutch line.

4.

Check the clutch cover assembly and the clutch disc assembly.