This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B278187 | Steering Lock System Missing Message | No communication between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) for 10 seconds or more. | ·
Certification ECU (smart key ECU assembly) ·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
Wire harness or connector |
Entry&Start | A |
Inspect the fuses for circuits related to this system before performing the following procedure.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| B278187 and B278588 are not output | A |
| Only B278187 is output | B |
| None of the above conditions are met | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Pre-procedure1
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71)Location & Routingewd_type=routing;type=c;code=H71 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=1 |
||
| H71-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71)Location & Routingewd_type=routing;type=c;code=H71 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=7 |
||
| H71-7 (B) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| except HV Model | A |
| for HV Model | B |
A
B
Pre-procedure1
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71,H46)Location & Routingewd_type=routing;type=c,c;code=H71,H46 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=5 Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H46;pinno=8 |
||
| H71-5 (LIN) - H46-8 (LIN) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71)Location & Routingewd_type=routing;type=c;code=H71 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=5 |
||
| H71-5 (LIN) - Body ground | Always | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71,H46)Location & Routingewd_type=routing;type=c,c;code=H71,H46 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=5 Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H46;pinno=8 |
||
| H71-5 (LIN) - H46-8 (LIN) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG