This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B278588 | Communication between ECUs connected by LIN Bus off | No communication between steering lock ECU (steering lock actuator or upper bracket assembly) and certification ECU (smart key ECU assembly) for 10 seconds or more. | ·
Certification ECU (smart key ECU assembly) ·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
Wire harness or connector |
Entry&Start | A |
except Gasolin Model TMC Made
for Gasolin Model TMC Made
Inspect the fuses for circuits related to this system before performing the following procedure.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for Gasolin Model TMC Made | A |
| except Gasolin Model TMC Made | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| B278588 is output | A |
| B278588 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71)Location & Routingewd_type=routing;type=c;code=H71 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=1 |
||
| H71-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71)Location & Routingewd_type=routing;type=c;code=H71 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=7 |
||
| H71-7 (B) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71,H46)Location & Routingewd_type=routing;type=c,c;code=H71,H46 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=5 Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H46;pinno=8 |
||
| H71-5 (LIN) - H46-8 (LIN) | Always | Below 1 Ω |
| H71-5 (LIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H71)Location & Routingewd_type=routing;type=c;code=H71 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=5 |
||
| H71-5 (LIN) - Body ground | Ignition switch ON | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| B278588 is output | A |
| B278588 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B278588 is output | A |
| B278588 is not output | B |
Post-procedure1
None
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Disconnect the H67 ID code box (immobiliser code ECU) connector.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B278588 is output | A |
| B278588 is not output | B |
Post-procedure1
None
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Disconnect the H67 ID code box (immobiliser code ECU) connector.
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H46,H71)Location & Routingewd_type=routing;type=c,c;code=H46,H71 Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H46;pinno=8 Click Connector(H71)Instrument Panel>Instrument Panel Wire / Speaker Wire>Steering Lock Actuator or Upper Bracket Assemblyewd_type=component;type=c;code=H71;pinno=5 |
||
| H46-8 (LIN) - H71-5 (LIN) | Always | Below 1 Ω |
| H46-8 (LIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG