The air conditioner pressure sensor, which is installed to the high pressure side pipe to detect refrigerant pressure, sends a refrigerant pressure signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly converts this signal to a pressure value according to the sensor characteristics and uses it to control the compressor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P053015 | Refrigerant Pressure Sensor Circuit Short to Battery or Open | Diagnosis Condition:
Ignition switch ON Malfunction Status: Open or short in air conditioner pressure sensor circuit Detection Time: Continuously for 4 seconds or more |
·
Air conditioner pressure sensor ·
Harness or connector ·
Air conditioning amplifier assembly |
Memorized | Air Conditioner | A |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ |
| Malfunction | Open in air conditioner pressure sensor circuit | ○ | - |
| Short in air conditioner pressure sensor circuit | - | ○ | |
| Detection Time | Continuously for 4 seconds or more | Continuously for 4 seconds or more | |
| Trip Count | 1 trip | 1 trip | |
If the conditions of either of these patterns are detected, a DTC will be stored
Pre-procedure1
Install a manifold gauge set.
Procedure1
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Regulator Pressure Sensor | Air conditioner pressure sensor | Min.: -32.768 MPaG
Max.: 32.767 MPaG |
Actual refrigerant pressure displayed | ·
Refrigerant line (gas leak etc.) ·
Air conditioner pressure sensor circuit malfunction |
| Tester Display |
|---|
| Regulator Pressure Sensor |
Compare the values displayed in the Data List and on the manifold gauge set.
| Result | Proceed to |
|---|---|
| The values displayed in the Data List and on the manifold gauge set does not match | A |
| The values displayed in the Data List and on the manifold gauge set match | B |
Post-procedure1
None
A
B
for HFC-134a(R134a): Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION
for HFO-1234yf(R1234yf): Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>ON-VEHICLE INSPECTION
Pre-procedure1
Disconnect the A51 air conditioner pressure sensor connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51)Location & Routingewd_type=routing;type=c;code=A51 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=1 |
||
| A51-1 (-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51)Location & Routingewd_type=routing;type=c;code=A51 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=2 |
||
| A51-2 (PR) - Body ground | Ignition switch ON | 3.0 to 5.25 V |
| Result | Proceed to |
|---|---|
| A51-2 (PR) - Body ground is more than 5.25 V | A |
| A51-2 (PR) - Body ground is more than or equal to 3.0 and less than or equal to 5.25 V | B |
| A51-2 (PR) - Body ground is less than 3.0 V | C |
A
B
C
Pre-procedure1
Disconnect the H23 air conditioning amplifier assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51,H23)Location & Routingewd_type=routing;type=c,c;code=A51,H23 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=2 Click Connector(H23)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=H23;pinno=36 |
||
| A51-2 (PR) or H23-36 (PRE) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51)Location & Routingewd_type=routing;type=c;code=A51 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=3,2 |
||
| A51-3 (+) - A51-2 (PR) | Ignition switch off | 180 to 220 kΩ |
After turning the ignition switch off, wait at least 30 seconds before performing the measurement.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the H23 air conditioning amplifier assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51,H23)Location & Routingewd_type=routing;type=c,c;code=A51,H23 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=2,3 Click Connector(H23)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=H23;pinno=36,11 |
||
| A51-2 (PR) or H23-36 (PRE) - A51-3 (+) or H23-11 (S5-3) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H23 air conditioning amplifier assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51,H23)Location & Routingewd_type=routing;type=c,c;code=A51,H23 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=2 Click Connector(H23)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=H23;pinno=36 |
||
| A51-2 (PR) - H23-36 (PRE) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H23 air conditioning amplifier assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51,H23)Location & Routingewd_type=routing;type=c,c;code=A51,H23 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=1 Click Connector(H23)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=H23;pinno=12 |
||
| A51-1 (-) - H23-12 (SG-4) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG