Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2021.07
RM3700E _59 Vehicle Exterior _092998 WINDOW / GLASS _0438363 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies. The power window regulator motor assemblies have motor, regulator and ECU functions.

This DTC is stored when the ECU built into a power window regulator motor assembly and multiplex network master switch assembly determine that the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly is stuck.

Master Switch
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2312 Power Window Switch Malfunction
·

Multiplex network master switch assembly stuck

·

Multiplex network master switch assembly held in same position for more than 20 seconds

·

Multiplex network master switch assembly operated for 20 seconds or more


Multiplex network master switch assembly Master Switch A

D-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2312 Power Window Switch Malfunction
·

Multiplex network master switch assembly stuck

·

Multiplex network master switch assembly held in same position for more than 20 seconds


·

Multiplex network master switch assembly

·

Power window regulator motor assembly (for driver door)

·

Wire harness or connector


D-Door Motor A

P-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2312 Power Window Switch Malfunction
·

Power window regulator switch assembly stuck

·

Power window regulator switch assembly held in same position for more than 20 seconds


·

Power window regulator switch assembly

·

Power window regulator motor assembly (for front passenger door)

·

Wire harness or connector


P-Door Motor A

RL-Door Motor (w/ Rear Power Window)
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2312 Power Window Switch Malfunction
·

Rear power window regulator switch assembly (for LH door) stuck

·

Rear power window regulator switch assembly (for LH door) held in same position for more than 20 seconds


·

Rear power window regulator switch assembly (for LH door)

·

Power window regulator motor assembly (for rear LH door)

·

Wire harness or connector


RL-Door Motor A

RR-Door Motor (w/ Rear Power Window)
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2312 Power Window Switch Malfunction
·

Rear power window regulator switch assembly (for RH door) stuck

·

Rear power window regulator switch assembly (for RH door) held in same position for more than 20 seconds


·

Rear power window regulator switch assembly (for RH door)

·

Power window regulator motor assembly (for rear RH door)

·

Wire harness or connector


RR-Door Motor A

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2312 is stored in the multiplex network master switch assembly and in each power window regulator motor assembly.

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



HINT:

If DTC B2312 is not output again after the DTC has been cleared, the DTC was stored due to the switch being held in the same position continuously.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for LHD without Rear Power Window A
for RHD without Rear Power Window B
for LHD with Rear Power Window C
for RHD with Rear Power Window D



A

2.CHECK FOR DTC

B

17.CHECK FOR DTC

C

32.CHECK FOR DTC

D

63.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Master Switch > Trouble Codes
50001 148
Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144

Result:
Result Proceed to
Any Master Switch DTCs in the table below are output A
Any D-Door Motor DTCs in the table below are output B
Any P-Door Motor DTCs in the table below are output C
No DTCs in the table below are output D


Malfunction Status System Related DTCs
Power Window Switch Malfunction Master Switch B2312 ON Switch Failure
D-Door Motor B2312 Master Switch of Driver side door Malfunction
P-Door Motor B2312 Power Window Switch of Passenger side door Malfunction


A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

3.READ VALUE USING GTS (D-DOOR MOTOR)

C

9.READ VALUE USING GTS (P-DOOR MOTOR)

D

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

3.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not being operated -
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
50003 124 2

Result:
Result Proceed to
The value of D Door P/W Up SW is OFF A
None of the above conditions are met B



A

4.READ VALUE USING GTS (D-DOOR MOTOR)

B

7.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
4.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON ON: Driver door power window manual up switch being operated -
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
50003 124 2

Result:
Result Proceed to
The value of D Door P/W Up SW is ON A
None of the above conditions are met B



A

5.READ VALUE USING GTS (D-DOOR MOTOR)

B

7.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
5.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Down SW
50003 124 3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Result Proceed to
The value of D Door P/W Down SW is OFF A
None of the above conditions are met B



A

6.READ VALUE USING GTS (D-DOOR MOTOR)

B

7.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
6.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Down SW
50003 124 3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Result Proceed to
The value of D Door P/W Down SW is OFF A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

B

7.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
7.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the L7 power window regulator motor assembly (for driver door) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L7)Location & Routing

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

L7-10 (UP) - Body ground Ignition switch ON 11 to 14 V
L7-7 (DOWN) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
8.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

Pre-procedure1

a.

Disconnect the L13 multiplex network master switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L13,L7)Location & Routing

Click Connector(L13)Body>Front Door Wire LH / Television Camera Wire>Multiplex Network Master Switch Assembly

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

L13-20 (UP) or L7-10 (UP) - Body ground Always 10 kΩ or higher
L13-15 (DOWN) or L7-7 (DOWN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON OFF: Front passenger door power window auto up or auto down switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
50003 144 1

Result:
Result Proceed to
The value of P Door P/W Auto SW is OFF A
None of the above conditions are met B



A

10.READ VALUE USING GTS (P-DOOR MOTOR)

B

15.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
10.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON ON: Front passenger door power window auto up or auto down switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
50003 144 1

Result:
Result Proceed to
The value of P Door P/W Auto SW is ON A
None of the above conditions are met B



A

11.READ VALUE USING GTS (P-DOOR MOTOR)

B

15.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
11.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON OFF: Front passenger door power window manual up switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Up SW
50003 144 2

Result:
Result Proceed to
The value of P Door P/W Up SW is OFF A
None of the above conditions are met B



A

12.READ VALUE USING GTS (P-DOOR MOTOR)

B

15.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
12.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON ON: Front passenger door power window manual up switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Up SW
50003 144 2

Result:
Result Proceed to
The value of P Door P/W Up SW is ON A
None of the above conditions are met B



A

13.READ VALUE USING GTS (P-DOOR MOTOR)

B

15.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
13.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON OFF: Front passenger door power window manual down switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Down SW
50003 144 3

Result:
Result Proceed to
The value of P Door P/W Down SW is OFF A
None of the above conditions are met B



A

14.READ VALUE USING GTS (P-DOOR MOTOR)

B

15.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
14.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON ON: Front passenger door power window manual down switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Down SW
50003 144 3

Result:
Result Proceed to
The value of P Door P/W Down SW is ON A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

B

15.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
15.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK

16.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

Pre-procedure1

a.

Disconnect the K7 power window regulator motor assembly (for Front Passenger Door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K14,K7)Location & Routing

Click Connector(K14)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Switch Assembly RH

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

K14-5 (UP) or K7-10 (UP) - Body ground Always 10 kΩ or higher
K14-8 (AUTO) or K7-4 (AUTO) - Body ground Always 10 kΩ or higher
K14-4 (DOWN) or K7-7 (DOWN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Master Switch > Trouble Codes
50001 148
Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144

Result:
Result Proceed to
Any Master Switch DTCs in the table below are output A
Any D-Door Motor DTCs in the table below are output B
Any P-Door Motor DTCs in the table below are output C
No DTCs in the table below are output D


Malfunction Status System Related DTCs
Power Window Switch Malfunction Master Switch B2312 ON Switch Failure
D-Door Motor B2312 Master Switch of Driver side door Malfunction
P-Door Motor B2312 Power Window Switch of Passenger side door Malfunction


A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

18.READ VALUE USING GTS (D-DOOR MOTOR)

C

24.READ VALUE USING GTS (P-DOOR MOTOR)

D

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

18.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not being operated -
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
50003 124 2

Result:
Result Proceed to
The value of D Door P/W Up SW is OFF A
None of the above conditions are met B



A

19.READ VALUE USING GTS (D-DOOR MOTOR)

B

22.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
19.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON ON: Driver door power window manual up switch being operated -
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
50003 124 2

Result:
Result Proceed to
The value of D Door P/W Up SW is ON A
None of the above conditions are met B



A

20.READ VALUE USING GTS (D-DOOR MOTOR)

B

22.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
20.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Down SW
50003 124 3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Result Proceed to
The value of D Door P/W Down SW is OFF A
None of the above conditions are met B



A

21.READ VALUE USING GTS (D-DOOR MOTOR)

B

22.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
21.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Down SW
50003 124 3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Result Proceed to
The value of D Door P/W Down SW is OFF A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

B

22.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
22.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the K7 power window regulator motor assembly (for driver door) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(K7)Location & Routing

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

K7-10 (UP) - Body ground Ignition switch ON 11 to 14 V
K7-7 (DOWN) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

23.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
23.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

Pre-procedure1

a.

Disconnect the K5 multiplex network master switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K5,K7)Location & Routing

Click Connector(K5)Body>Front Door Wire RH / Television Camera Wire>Multiplex Network Master Switch Assembly

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

K5-20 (UP) or K7-10 (UP) - Body ground Always 10 kΩ or higher
K5-15 (DOWN) or K7-7 (DOWN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON OFF: Front passenger door power window auto up or auto down switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
50003 144 1

Result:
Result Proceed to
The value of P Door P/W Auto SW is OFF A
None of the above conditions are met B



A

25.READ VALUE USING GTS (P-DOOR MOTOR)

B

30.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
25.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON ON: Front passenger door power window auto up or auto down switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
50003 144 1

Result:
Result Proceed to
The value of P Door P/W Auto SW is ON A
None of the above conditions are met B



A

26.READ VALUE USING GTS (P-DOOR MOTOR)

B

30.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
26.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON OFF: Front passenger door power window manual up switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Up SW
50003 144 2

Result:
Result Proceed to
The value of P Door P/W Up SW is OFF A
None of the above conditions are met B



A

27.READ VALUE USING GTS (P-DOOR MOTOR)

B

30.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
27.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON ON: Front passenger door power window manual up switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Up SW
50003 144 2

Result:
Result Proceed to
The value of P Door P/W Up SW is ON A
None of the above conditions are met B



A

28.READ VALUE USING GTS (P-DOOR MOTOR)

B

30.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
28.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON OFF: Front passenger door power window manual down switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Down SW
50003 144 3

Result:
Result Proceed to
The value of P Door P/W Down SW is OFF A
None of the above conditions are met B



A

29.READ VALUE USING GTS (P-DOOR MOTOR)

B

30.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
29.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON ON: Front passenger door power window manual down switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Down SW
50003 144 3

Result:
Result Proceed to
The value of P Door P/W Down SW is ON A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

B

30.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
30.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK

31.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

31.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

Pre-procedure1

a.

Disconnect the L7 power window regulator motor assembly (for Front Passenger Door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L6,L7)Location & Routing

Click Connector(L6)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Switch Assembly LH

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

L6-5 (UP) or L7-10 (UP) - Body ground Always 10 kΩ or higher
L6-8 (AUTO) or L7-4 (AUTO) - Body ground Always 10 kΩ or higher
L6-4 (DOWN) or L7-7 (DOWN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Master Switch > Trouble Codes
50001 148
Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144
Body Electrical > RL-Door Motor > Trouble Codes
50001 146
Body Electrical > RR-Door Motor > Trouble Codes
50001 145

Result:
Result Proceed to
Any Master Switch DTCs in the table below are output A
Any D-Door Motor DTCs in the table below are output B
Any P-Door Motor DTCs in the table below are output C
Any RL-Door Motor DTCs in the table below are output D
Any RR-Door Motor DTCs in the table below are output E
No DTCs in the table below are output F


Malfunction Status System Related DTCs
Power Window Switch Malfunction Master Switch B2312 ON Switch Failure
D-Door Motor B2312 Master Switch of Driver side door Malfunction
P-Door Motor B2312 Power Window Switch of Passenger side door Malfunction
RL-Door Motor B2312 Power Window Switch of Rear Left side door Malfunction
RR-Door Motor B2312 Power Window Switch of Rear Right side door Malfunction


A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

33.READ VALUE USING GTS (D-DOOR MOTOR)

C

39.READ VALUE USING GTS (P-DOOR MOTOR)

D

47.READ VALUE USING GTS (RL-DOOR MOTOR)

E

55.READ VALUE USING GTS (RR-DOOR MOTOR)

F

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

33.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not being operated -
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
50003 124 2

Result:
Result Proceed to
The value of D Door P/W Up SW is OFF A
None of the above conditions are met B



A

34.READ VALUE USING GTS (D-DOOR MOTOR)

B

37.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
34.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON ON: Driver door power window manual up switch being operated -
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
50003 124 2

Result:
Result Proceed to
The value of D Door P/W Up SW is ON A
None of the above conditions are met B



A

35.READ VALUE USING GTS (D-DOOR MOTOR)

B

37.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
35.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Down SW
50003 124 3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Result Proceed to
The value of D Door P/W Down SW is OFF A
None of the above conditions are met B



A

36.READ VALUE USING GTS (D-DOOR MOTOR)

B

37.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
36.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Down SW
50003 124 3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Result Proceed to
The value of D Door P/W Down SW is OFF A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

B

37.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
37.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the L7 power window regulator motor assembly (for driver door) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(L7)Location & Routing

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

L7-10 (UP) - Body ground Ignition switch ON 11 to 14 V
L7-7 (DOWN) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

38.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
38.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

Pre-procedure1

a.

Disconnect the L13 multiplex network master switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L13,L7)Location & Routing

Click Connector(L13)Body>Front Door Wire LH / Television Camera Wire>Multiplex Network Master Switch Assembly

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

L13-20 (UP) or L7-10 (UP) - Body ground Always 10 kΩ or higher
L13-15 (DOWN) or L7-7 (DOWN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON OFF: Front passenger door power window auto up or auto down switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
50003 144 1

Result:
Result Proceed to
The value of P Door P/W Auto SW is OFF A
None of the above conditions are met B



A

40.READ VALUE USING GTS (P-DOOR MOTOR)

B

45.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
40.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON ON: Front passenger door power window auto up or auto down switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
50003 144 1

Result:
Result Proceed to
The value of P Door P/W Auto SW is ON A
None of the above conditions are met B



A

41.READ VALUE USING GTS (P-DOOR MOTOR)

B

45.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
41.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON OFF: Front passenger door power window manual up switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Up SW
50003 144 2

Result:
Result Proceed to
The value of P Door P/W Up SW is OFF A
None of the above conditions are met B



A

42.READ VALUE USING GTS (P-DOOR MOTOR)

B

45.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
42.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON ON: Front passenger door power window manual up switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Up SW
50003 144 2

Result:
Result Proceed to
The value of P Door P/W Up SW is ON A
None of the above conditions are met B



A

43.READ VALUE USING GTS (P-DOOR MOTOR)

B

45.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
43.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON OFF: Front passenger door power window manual down switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Down SW
50003 144 3

Result:
Result Proceed to
The value of P Door P/W Down SW is OFF A
None of the above conditions are met B



A

44.READ VALUE USING GTS (P-DOOR MOTOR)

B

45.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
44.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON ON: Front passenger door power window manual down switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Down SW
50003 144 3

Result:
Result Proceed to
The value of P Door P/W Down SW is ON A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

B

45.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
45.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK

46.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

46.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

Pre-procedure1

a.

Disconnect the K7 power window regulator motor assembly (for Front Passenger Door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K14,K7)Location & Routing

Click Connector(K14)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Switch Assembly RH

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

K14-5 (UP) or K7-10 (UP) - Body ground Always 10 kΩ or higher
K14-8 (AUTO) or K7-4 (AUTO) - Body ground Always 10 kΩ or higher
K14-4 (DOWN) or K7-7 (DOWN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

47.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear LH door power window auto switch signal OFF or ON OFF: Rear LH door power window auto up or auto down switch not being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Auto SW
50003 146 1

Result:
Result Proceed to
The value of RL Door P/W Auto SW is OFF A
None of the above conditions are met B



A

48.READ VALUE USING GTS (RL-DOOR MOTOR)

B

53.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
48.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear LH door power window auto switch signal OFF or ON ON: Rear LH door power window auto up or auto down switch being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Auto SW
50003 146 1

Result:
Result Proceed to
The value of RL Door P/W Auto SW is ON A
None of the above conditions are met B



A

49.READ VALUE USING GTS (RL-DOOR MOTOR)

B

53.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
49.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Up SW Rear LH door power window manual up switch signal OFF or ON OFF: Rear LH door power window manual up switch not being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Up SW
50003 146 2

Result:
Result Proceed to
The value of RL Door P/W Up SW is OFF A
None of the above conditions are met B



A

50.READ VALUE USING GTS (RL-DOOR MOTOR)

B

53.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
50.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Up SW Rear LH door power window manual up switch signal OFF or ON ON: Rear LH door power window manual up switch being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Up SW
50003 146 2

Result:
Result Proceed to
The value of RL Door P/W Up SW is ON A
None of the above conditions are met B



A

51.READ VALUE USING GTS (RL-DOOR MOTOR)

B

53.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
51.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Down SW Rear LH door power window manual down switch signal OFF or ON OFF: Rear LH door power window manual down switch not being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Down SW
50003 146 3

Result:
Result Proceed to
The value of RL Door P/W Down SW is OFF A
None of the above conditions are met B



A

52.READ VALUE USING GTS (RL-DOOR MOTOR)

B

53.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
52.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Down SW Rear LH door power window manual down switch signal OFF or ON ON: Rear LH door power window manual down switch being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Down SW
50003 146 3

Result:
Result Proceed to
The value of RL Door P/W Down SW is ON A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

B

53.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
53.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

OK

54.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

54.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

Pre-procedure1

a.

Disconnect the N4 power window regulator motor assembly (for Rear LH Door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3,N4)Location & Routing

Click Connector(N3)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Switch Assembly LH

Click Connector(N4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

N3-5 (UP) or N4-10 (UP) - Body ground Always 10 kΩ or higher
N3-4 (DOWN) or N4-7 (DOWN) - Body ground Always 10 kΩ or higher
N3-8 (AUTO) or N4-4 (AUTO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear RH door power window auto switch signal OFF or ON OFF: Rear RH door power window auto up or auto down switch not being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Auto SW
50003 145 1

Result:
Result Proceed to
The value of RR Door P/W Auto SW is OFF A
None of the above conditions are met B



A

56.READ VALUE USING GTS (RR-DOOR MOTOR)

B

61.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
56.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear RH door power window auto switch signal OFF or ON ON: Rear RH door power window auto up or auto down switch being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Auto SW
50003 145 1

Result:
Result Proceed to
The value of RR Door P/W Auto SW is ON A
None of the above conditions are met B



A

57.READ VALUE USING GTS (RR-DOOR MOTOR)

B

61.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
57.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Up SW Rear RH door power window manual up switch signal OFF or ON OFF: Rear RH door power window manual up switch not being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Up SW
50003 145 2

Result:
Result Proceed to
The value of RR Door P/W Up SW is OFF A
None of the above conditions are met B



A

58.READ VALUE USING GTS (RR-DOOR MOTOR)

B

61.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
58.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Up SW Rear RH door power window manual up switch signal OFF or ON ON: Rear RH door power window manual up switch being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Up SW
50003 145 2

Result:
Result Proceed to
The value of RR Door P/W Up SW is ON A
None of the above conditions are met B



A

59.READ VALUE USING GTS (RR-DOOR MOTOR)

B

61.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
59.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Down SW Rear RH door power window manual down switch signal OFF or ON OFF: Rear RH door power window manual down switch not being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Down SW
50003 145 3

Result:
Result Proceed to
The value of RR Door P/W Down SW is OFF A
None of the above conditions are met B



A

60.READ VALUE USING GTS (RR-DOOR MOTOR)

B

61.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
60.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Down SW Rear RH door power window manual down switch signal OFF or ON ON: Rear RH door power window manual down switch being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Down SW
50003 145 3

Result:
Result Proceed to
The value of RR Door P/W Down SW is ON A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

B

61.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
61.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

OK

62.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

62.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

Pre-procedure1

a.

Disconnect the M4 power window regulator motor assembly (for rear RH door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M3,M4)Location & Routing

Click Connector(M3)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Switch Assembly RH

Click Connector(M4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

M3-5 (UP) or M4-10 (UP) - Body ground Always 10 kΩ or higher
M3-4 (DOWN) or M4-7 (DOWN) - Body ground Always 10 kΩ or higher
M3-8 (AUTO) or M4-4 (AUTO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

63.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Master Switch > Trouble Codes
50001 148
Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144
Body Electrical > RL-Door Motor > Trouble Codes
50001 146
Body Electrical > RR-Door Motor > Trouble Codes
50001 145

Result:
Result Proceed to
Any Master Switch DTCs in the table below are output A
Any D-Door Motor DTCs in the table below are output B
Any P-Door Motor DTCs in the table below are output C
Any RL-Door Motor DTCs in the table below are output D
Any RR-Door Motor DTCs in the table below are output E
No DTCs in the table below are output F


Malfunction Status System Related DTCs
Power Window Switch Malfunction Master Switch B2312 ON Switch Failure
D-Door Motor B2312 Master Switch of Driver side door Malfunction
P-Door Motor B2312 Power Window Switch of Passenger side door Malfunction
RL-Door Motor B2312 Power Window Switch of Rear Left side door Malfunction
RR-Door Motor B2312 Power Window Switch of Rear Right side door Malfunction


A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

64.READ VALUE USING GTS (D-DOOR MOTOR)

C

70.READ VALUE USING GTS (P-DOOR MOTOR)

D

78.READ VALUE USING GTS (RL-DOOR MOTOR)

E

86.READ VALUE USING GTS (RR-DOOR MOTOR)

F

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

64.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not being operated -
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
50003 124 2

Result:
Result Proceed to
The value of D Door P/W Up SW is OFF A
None of the above conditions are met B



A

65.READ VALUE USING GTS (D-DOOR MOTOR)

B

68.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
65.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON ON: Driver door power window manual up switch being operated -
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
50003 124 2

Result:
Result Proceed to
The value of D Door P/W Up SW is ON A
None of the above conditions are met B



A

66.READ VALUE USING GTS (D-DOOR MOTOR)

B

68.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
66.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Down SW
50003 124 3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Result Proceed to
The value of D Door P/W Down SW is OFF A
None of the above conditions are met B



A

67.READ VALUE USING GTS (D-DOOR MOTOR)

B

68.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
67.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Down SW
50003 124 3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Result Proceed to
The value of D Door P/W Down SW is OFF A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

B

68.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
68.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the K7 power window regulator motor assembly (for driver door) connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(K7)Location & Routing

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

K7-10 (UP) - Body ground Ignition switch ON 11 to 14 V
K7-7 (DOWN) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

69.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
69.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

Pre-procedure1

a.

Disconnect the K5 multiplex network master switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K5,K7)Location & Routing

Click Connector(K5)Body>Front Door Wire RH / Television Camera Wire>Multiplex Network Master Switch Assembly

Click Connector(K7)Body>Front Door Wire RH / Television Camera Wire>Front Power Window Regulator Motor Assembly RH

K5-20 (UP) or K7-10 (UP) - Body ground Always 10 kΩ or higher
K5-15 (DOWN) or K7-7 (DOWN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

70.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON OFF: Front passenger door power window auto up or auto down switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
50003 144 1

Result:
Result Proceed to
The value of P Door P/W Auto SW is OFF A
None of the above conditions are met B



A

71.READ VALUE USING GTS (P-DOOR MOTOR)

B

76.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
71.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON ON: Front passenger door power window auto up or auto down switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
50003 144 1

Result:
Result Proceed to
The value of P Door P/W Auto SW is ON A
None of the above conditions are met B



A

72.READ VALUE USING GTS (P-DOOR MOTOR)

B

76.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
72.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON OFF: Front passenger door power window manual up switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Up SW
50003 144 2

Result:
Result Proceed to
The value of P Door P/W Up SW is OFF A
None of the above conditions are met B



A

73.READ VALUE USING GTS (P-DOOR MOTOR)

B

76.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
73.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON ON: Front passenger door power window manual up switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Up SW
50003 144 2

Result:
Result Proceed to
The value of P Door P/W Up SW is ON A
None of the above conditions are met B



A

74.READ VALUE USING GTS (P-DOOR MOTOR)

B

76.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
74.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON OFF: Front passenger door power window manual down switch not being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Down SW
50003 144 3

Result:
Result Proceed to
The value of P Door P/W Down SW is OFF A
None of the above conditions are met B



A

75.READ VALUE USING GTS (P-DOOR MOTOR)

B

76.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
75.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON ON: Front passenger door power window manual down switch being operated -
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Down SW
50003 144 3

Result:
Result Proceed to
The value of P Door P/W Down SW is ON A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

B

76.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
76.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK

77.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

77.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

Pre-procedure1

a.

Disconnect the L7 power window regulator motor assembly (for Front Passenger Door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L6,L7)Location & Routing

Click Connector(L6)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Switch Assembly LH

Click Connector(L7)Body>Front Door Wire LH / Television Camera Wire>Front Power Window Regulator Motor Assembly LH

L6-5 (UP) or L7-10 (UP) - Body ground Always 10 kΩ or higher
L6-8 (AUTO) or L7-4 (AUTO) - Body ground Always 10 kΩ or higher
L6-4 (DOWN) or L7-7 (DOWN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

78.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear LH door power window auto switch signal OFF or ON OFF: Rear LH door power window auto up or auto down switch not being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Auto SW
50003 146 1

Result:
Result Proceed to
The value of RL Door P/W Auto SW is OFF A
None of the above conditions are met B



A

79.READ VALUE USING GTS (RL-DOOR MOTOR)

B

84.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
79.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear LH door power window auto switch signal OFF or ON ON: Rear LH door power window auto up or auto down switch being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Auto SW
50003 146 1

Result:
Result Proceed to
The value of RL Door P/W Auto SW is ON A
None of the above conditions are met B



A

80.READ VALUE USING GTS (RL-DOOR MOTOR)

B

84.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
80.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Up SW Rear LH door power window manual up switch signal OFF or ON OFF: Rear LH door power window manual up switch not being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Up SW
50003 146 2

Result:
Result Proceed to
The value of RL Door P/W Up SW is OFF A
None of the above conditions are met B



A

81.READ VALUE USING GTS (RL-DOOR MOTOR)

B

84.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
81.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Up SW Rear LH door power window manual up switch signal OFF or ON ON: Rear LH door power window manual up switch being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Up SW
50003 146 2

Result:
Result Proceed to
The value of RL Door P/W Up SW is ON A
None of the above conditions are met B



A

82.READ VALUE USING GTS (RL-DOOR MOTOR)

B

84.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
82.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Down SW Rear LH door power window manual down switch signal OFF or ON OFF: Rear LH door power window manual down switch not being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Down SW
50003 146 3

Result:
Result Proceed to
The value of RL Door P/W Down SW is OFF A
None of the above conditions are met B



A

83.READ VALUE USING GTS (RL-DOOR MOTOR)

B

84.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
83.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Down SW Rear LH door power window manual down switch signal OFF or ON ON: Rear LH door power window manual down switch being operated -
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Down SW
50003 146 3

Result:
Result Proceed to
The value of RL Door P/W Down SW is ON A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

B

84.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
84.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

OK

85.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

85.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

Pre-procedure1

a.

Disconnect the N4 power window regulator motor assembly (for Rear LH Door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3,N4)Location & Routing

Click Connector(N3)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Switch Assembly LH

Click Connector(N4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

N3-5 (UP) or N4-10 (UP) - Body ground Always 10 kΩ or higher
N3-4 (DOWN) or N4-7 (DOWN) - Body ground Always 10 kΩ or higher
N3-8 (AUTO) or N4-4 (AUTO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

86.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear RH door power window auto switch signal OFF or ON OFF: Rear RH door power window auto up or auto down switch not being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Auto SW
50003 145 1

Result:
Result Proceed to
The value of RR Door P/W Auto SW is OFF A
None of the above conditions are met B



A

87.READ VALUE USING GTS (RR-DOOR MOTOR)

B

92.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
87.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear RH door power window auto switch signal OFF or ON ON: Rear RH door power window auto up or auto down switch being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Auto SW
50003 145 1

Result:
Result Proceed to
The value of RR Door P/W Auto SW is ON A
None of the above conditions are met B



A

88.READ VALUE USING GTS (RR-DOOR MOTOR)

B

92.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
88.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Up SW Rear RH door power window manual up switch signal OFF or ON OFF: Rear RH door power window manual up switch not being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Up SW
50003 145 2

Result:
Result Proceed to
The value of RR Door P/W Up SW is OFF A
None of the above conditions are met B



A

89.READ VALUE USING GTS (RR-DOOR MOTOR)

B

92.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
89.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Up SW Rear RH door power window manual up switch signal OFF or ON ON: Rear RH door power window manual up switch being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Up SW
50003 145 2

Result:
Result Proceed to
The value of RR Door P/W Up SW is ON A
None of the above conditions are met B



A

90.READ VALUE USING GTS (RR-DOOR MOTOR)

B

92.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
90.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Down SW Rear RH door power window manual down switch signal OFF or ON OFF: Rear RH door power window manual down switch not being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Down SW
50003 145 3

Result:
Result Proceed to
The value of RR Door P/W Down SW is OFF A
None of the above conditions are met B



A

91.READ VALUE USING GTS (RR-DOOR MOTOR)

B

92.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
91.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Down SW Rear RH door power window manual down switch signal OFF or ON ON: Rear RH door power window manual down switch being operated -
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Down SW
50003 145 3

Result:
Result Proceed to
The value of RR Door P/W Down SW is ON A
None of the above conditions are met B



A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

B

92.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
92.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

OK

93.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

93.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

Pre-procedure1

a.

Disconnect the M4 power window regulator motor assembly (for rear RH door) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M3,M4)Location & Routing

Click Connector(M3)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Switch Assembly RH

Click Connector(M4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

M3-5 (UP) or M4-10 (UP) - Body ground Always 10 kΩ or higher
M3-4 (DOWN) or M4-7 (DOWN) - Body ground Always 10 kΩ or higher
M3-8 (AUTO) or M4-4 (AUTO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR