Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model) › from 2021.07
RM3700E _58 Vehicle Interior _093020 HEATING / AIR CONDITIONING _0438859 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  P053011  Refrigerant Pressure Sensor Circuit Short to Ground  


DESCRIPTION

The air conditioner pressure sensor, which is installed to the high pressure side pipe to detect refrigerant pressure, sends a refrigerant pressure signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly converts this signal to a pressure value according to the sensor characteristics and uses it to control the compressor.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
P053011 Refrigerant Pressure Sensor Circuit Short to Ground Diagnosis Condition:

Ignition switch ON


Malfunction Status:

Short in air conditioner pressure sensor circuit


Detection Time:

Continuously for 4 seconds or more


·

Air conditioner pressure sensor

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized Air Conditioner A

WIRING DIAGRAM

E370470E38
2.146,0.396 2.302,0.594 0.156,0.198 10 false 3 2.156,0.865 2.313,1.063 0.156,0.198 10 false 2 2.156,1.344 2.313,1.542 0.156,0.198 10 false 1 1.948,0.396 2.104,0.594 0.156,0.198 10 false + 1.854,0.865 2.125,1.063 0.271,0.198 10 false PR 1.958,1.323 2.115,1.521 0.156,0.198 10 false - 0.375,2.021 0.646,2.219 0.271,0.198 10 false A51 0.365,2.167 2.531,2.385 2.167,0.219 10 false Air Conditioner Pressure Sensor 4.896,2.042 5.167,2.24 0.271,0.198 10 false H25 4.885,2.198 7.156,2.396 2.271,0.198 10 false Air Conditioning Amplifier Assembly 4.75,0.385 5.042,0.583 0.292,0.198 10 false 11 4.833,0.865 5.052,1.063 0.219,0.198 10 false 6 4.75,1.354 4.969,1.552 0.219,0.198 10 false 15 5.01,0.875 5.385,1.063 0.375,0.188 10 false PRE 5.01,0.396 5.385,0.583 0.375,0.188 10 false S5-3 5.01,1.344 5.385,1.531 0.375,0.188 10 false SG-4 5.729,0.313 6.104,0.5 0.375,0.188 10 false 5 V 6.469,0.979 6.844,1.167 0.375,0.188 10 false AD

PROCEDURE

1.CHECK REFRIGERANT PRESSURE

Pre-procedure1

a.

Install a manifold gauge set.


Procedure1

a.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Air conditioner pressure sensor Min.: -32.768 MPaG
Max.: 32.767 MPaG
Actual refrigerant pressure displayed
·

Refrigerant line (gas leak etc.)

·

Air conditioner pressure sensor circuit malfunction


Body Electrical > Air Conditioner > Data List
Tester Display
Regulator Pressure Sensor
50003 450 106

b.

Compare the values displayed in the Data List and on the manifold gauge set.

Result:
Result Proceed to
The values displayed in the Data List and on the manifold gauge set does not match A
The values displayed in the Data List and on the manifold gauge set match B



Post-procedure1

a.

None



A

2.READ VALUE USING GTS (REGULATOR PRESSURE SENSOR)

B

2.READ VALUE USING GTS (REGULATOR PRESSURE SENSOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Air conditioner pressure sensor Min.: -32.768 MPaG
Max.: 32.767 MPaG
Actual refrigerant pressure displayed
·

Refrigerant line (gas leak etc.)

·

Air conditioner pressure sensor circuit malfunction


Body Electrical > Air Conditioner > Data List
Tester Display
Regulator Pressure Sensor
50003 450 106
OK:

Disconnecting the A51 connector of the air conditioner pressure sensor causes the Data List value to change.



Result:
Result Proceed to
Regulator pressure sensor value changes A
Regulator pressure sensor value does not change B



A

3.CHECK TERMINAL VOLTAGE (AIR CONDITIONER PRESSURE SENSOR)

B

5.CHECK TERMINAL VOLTAGE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
3.CHECK TERMINAL VOLTAGE (AIR CONDITIONER PRESSURE SENSOR)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A51)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

A51-3 (+) - Body ground Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the H25 air conditioning amplifier assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A51,H25)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

Click Connector(H25)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assembly

A51-3 (+) - H25-11 (S5-3) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A51)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

A51-2 (PR) - Body ground Ignition switch ON 3.0 to 5.25 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the H25 air conditioning amplifier assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A51,H25)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

Click Connector(H25)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assembly

A51-2 (PR) or H25-6 (PRE) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR