Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model) › from 2021.07
RM3700E _58 Vehicle Interior _093020 HEATING / AIR CONDITIONING _0438859 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  P053015  Refrigerant Pressure Sensor Circuit Short to Battery or Open  


DESCRIPTION

The air conditioner pressure sensor, which is installed to the high pressure side pipe to detect refrigerant pressure, sends a refrigerant pressure signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly converts this signal to a pressure value according to the sensor characteristics and uses it to control the compressor.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
P053015 Refrigerant Pressure Sensor Circuit Short to Battery or Open Diagnosis Condition:

Ignition switch ON


Malfunction Status:

Open or short in air conditioner pressure sensor circuit


Detection Time:

Continuously for 4 seconds or more


·

Air conditioner pressure sensor

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized Air Conditioner A

DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
Malfunction Open in air conditioner pressure sensor circuit ○ -
Short in air conditioner pressure sensor circuit - ○
Detection Time Continuously for 4 seconds or more Continuously for 4 seconds or more
Trip Count 1 trip 1 trip

HINT:

If the conditions of either of these patterns are detected, a DTC will be stored


WIRING DIAGRAM

E370470E38
2.146,0.396 2.302,0.594 0.156,0.198 10 false 3 2.156,0.865 2.313,1.063 0.156,0.198 10 false 2 2.156,1.344 2.313,1.542 0.156,0.198 10 false 1 1.948,0.396 2.104,0.594 0.156,0.198 10 false + 1.854,0.865 2.125,1.063 0.271,0.198 10 false PR 1.958,1.323 2.115,1.521 0.156,0.198 10 false - 0.375,2.021 0.646,2.219 0.271,0.198 10 false A51 0.365,2.167 2.531,2.385 2.167,0.219 10 false Air Conditioner Pressure Sensor 4.896,2.042 5.167,2.24 0.271,0.198 10 false H25 4.885,2.198 7.156,2.396 2.271,0.198 10 false Air Conditioning Amplifier Assembly 4.75,0.385 5.042,0.583 0.292,0.198 10 false 11 4.833,0.865 5.052,1.063 0.219,0.198 10 false 6 4.75,1.354 4.969,1.552 0.219,0.198 10 false 15 5.01,0.875 5.385,1.063 0.375,0.188 10 false PRE 5.01,0.396 5.385,0.583 0.375,0.188 10 false S5-3 5.01,1.344 5.385,1.531 0.375,0.188 10 false SG-4 5.729,0.313 6.104,0.5 0.375,0.188 10 false 5 V 6.469,0.979 6.844,1.167 0.375,0.188 10 false AD

PROCEDURE

1.CHECK REGULATOR PRESSURE SENSOR

Pre-procedure1

a.

Install a manifold gauge set.


Procedure1

a.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Air conditioner pressure sensor Min.: -32.768 MPaG
Max.: 32.767 MPaG
Actual refrigerant pressure displayed
·

Refrigerant line (gas leak etc.)

·

Air conditioner pressure sensor circuit malfunction


Body Electrical > Air Conditioner > Data List
Tester Display
Regulator Pressure Sensor
50003 450 106

b.

Compare the values displayed in the Data List and on the manifold gauge set.

Result:
Result Proceed to
The values displayed in the Data List and on the manifold gauge set does not match A
The values displayed in the Data List and on the manifold gauge set match B



Post-procedure1

a.

None



A

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - BODY GROUND)

Pre-procedure1

a.

Disconnect the A51 air conditioner pressure sensor connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A51)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

A51-1 (-) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK TERMINAL VOLTAGE

NG

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
3.CHECK TERMINAL VOLTAGE
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A51)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

A51-2 (PR) - Body ground Ignition switch ON 3.0 to 5.25 V



Result:
Result Proceed to
A51-2 (PR) - Body ground is more than 5.25 V A
A51-2 (PR) - Body ground is more than or equal to 3.0 and less than or equal to 5.25 V B
A51-2 (PR) - Body ground is less than 3.0 V C



A

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

B

5.CHECK INTERNAL CIRCUIT RESISTANCE (AIR CONDITIONING AMPLIFIER ASSEMBLY)

C

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the H25 air conditioning amplifier assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A51,H25)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

Click Connector(H25)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assembly

A51-2 (PR) or H25-6 (PRE) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK INTERNAL CIRCUIT RESISTANCE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A51)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

A51-3 (+) - A51-2 (PR) Ignition switch off 180 to 220 kΩ


HINT:

After turning the ignition switch off, wait at least 30 seconds before performing the measurement.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the H25 air conditioning amplifier assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A51,H25)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

Click Connector(H25)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assembly

A51-2 (PR) or H25-6 (PRE) - A51-3 (+) or H25-11 (S5-3) Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the H25 air conditioning amplifier assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A51,H25)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

Click Connector(H25)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assembly

A51-2 (PR) - H25-6 (PRE) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

Pre-procedure1

a.

Disconnect the H25 air conditioning amplifier assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A51,H25)Location & Routing

Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensor

Click Connector(H25)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assembly

A51-1 (-) - H25-15 (SG-4) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR