Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB (for 2WD) › from 2021.07
RM3700E _52 Drivetrain _093736 AXLE AND DIFFERENTIAL _0441826 REAR AXLE HUB(for 2WD) G

AXLE AND DIFFERENTIAL  REAR AXLE HUB(for 2WD)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear axle hub on-vehicle inspection are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model TMC Made)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

HINT:
for HV Model TMC Made

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model TMC Made)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. DISABLE BRAKE CONTROL (for HV Model TMC Made)

Hide 3.REMOVE REAR WHEEL

Hide 4.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 5.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Hide 6.REMOVE REAR DISC

Hide 7.INSPECT REAR AXLE HUB BEARING LOOSENESS

a.
C444339

Using a dial indicator with magnetic base, check for looseness near the center of the rear axle hub and bearing assembly.

Maximum Looseness:

0.05 mm (0.00197 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.




b.

If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.


Hide 8.INSPECT REAR AXLE HUB RUNOUT

C444341

a.

Using a dial indicator with magnetic base, check for runout on the surface of the rear axle hub and bearing assembly outside the rear axle hub bolts.

Maximum Runout:

0.07 mm (0.00276 in.)


NOTICE:
·

Ensure that the dial indicator is set perpendicular to the measurement surface.

·

Make sure to install the tip of the dial indicator towards the outside of the rear axle hub bolts.

·

Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.




b.

If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.


Hide 9.INSTALL REAR DISC

Hide 10.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Hide 890C0A 11.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model TMC Made)

Hide 13. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HV Model TMC Made)

HINT:

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE


HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART