DTCs may be stored during the inspection procedure. Be sure to clear the DTCs and check that no DTCs are output after the inspection is finished.
1.INSPECT PRESSURE SENSOR
Check auxiliary battery voltage.
11 to 14 V (while the ignition switch is off)
Set a pedal effort gauge, SST and connect the GTS.
| *a | Pedal Effort Gauge |
| *b | SST (LSPV Gauge) |
| *c | SST (No. 1 Nipple) |
Set a pedal effort gauge and SST.
Connect the GTS to the DLC3 with the ignition switch off, park (P) selected and parking brake applied.
Turn the ignition switch to ON and turn the GTS on.
Bleed air from SST (LSPV gauge).
Inspect the reaction force pressure and servo pressure.
Enter the following menus: Chassis / Brake/EPB / Data List / Reaction Force Pressure and Servo Pressure.
| Tester Display |
|---|
| Reaction Force Pressure |
| Servo Pressure |
Check the value output from "Reaction Force Pressure" and "Servo Pressure" by depressing the brake pedal.
| Pedal Effort | Reaction Force Pressure
(MPa) |
Servo Pressure
(MPa) |
Front Right Wheel Hydraulic Pressure | Rear Left Wheel Hydraulic Pressure |
|---|---|---|---|---|
| 50 N (5 kgf, 11.2 lbf) | 0.01 to 0.81 | 1.00 to 5.00 | 0.70 to 4.70 MPa (7.1 to 47.9 kgf/cm2, 102 to 682 psi) | 0.70 to 4.70 MPa (7.1 to 47.9 kgf/cm2, 102 to 682 psi) |
| 100 N (10 kgf, 22.5 lbf) | 0.67 to 1.47 | 4.00 to 8.00 | 3.70 to 7.70 MPa (37.7 to 78.5 kgf/cm2, 537 to 1117 psi) | 3.70 to 7.70 MPa (37.7 to 78.5 kgf/cm2, 537 to 1117 psi) |
| 150 N (15 kgf, 33.7 lbf) | 1.33 to 2.13 | 6.80 to 10.8 | 6.50 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) | 6.50 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) |
| 200 N (20 kgf, 45.0 lbf) | 2.00 to 2.80 | 8.20 to 12.2 | 7.9 to 11.9 MPa (80.6 to 121.3 kgf/cm2, 1146 to 1726 psi) | 7.9 to 11.9 MPa (80.6 to 121.3 kgf/cm2, 1146 to 1726 psi) |
| Pedal Effort | Reaction Force Pressure
(MPa) |
Servo Pressure
(MPa) |
Front Left Wheel Hydraulic Pressure | Rear Left Wheel Hydraulic Pressure |
|---|---|---|---|---|
| 50 N (5 kgf, 11.2 lbf) | 0.01 to 0.81 | 1.00 to 5.00 | 0.70 to 4.70 MPa (7.1 to 47.9 kgf/cm2, 102 to 682 psi) | 0.70 to 4.70 MPa (7.1 to 47.9 kgf/cm2, 102 to 682 psi) |
| 100 N (10 kgf, 22.5 lbf) | 0.67 to 1.47 | 4.00 to 8.00 | 3.70 to 7.70 MPa (37.7 to 78.5 kgf/cm2, 537 to 1117 psi) | 3.70 to 7.70 MPa (37.7 to 78.5 kgf/cm2, 537 to 1117 psi) |
| 150 N (15 kgf, 33.7 lbf) | 1.33 to 2.13 | 6.80 to 10.8 | 6.50 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) | 6.50 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) |
| 200 N (20 kgf, 45.0 lbf) | 2.00 to 2.80 | 8.20 to 12.2 | 7.9 to 11.9 MPa (80.6 to 121.3 kgf/cm2, 1146 to 1726 psi) | 7.9 to 11.9 MPa (80.6 to 121.3 kgf/cm2, 1146 to 1726 psi) |
Remove the pedal effort gauge and SST.
Remove the pedal effort gauge and SST, and bleed the brake line.
Inspect the accumulator pressure.
Enter the following menus: Chassis / Brake/EPB / Data List / Accumulator Pressure and MT Voltage Value.
| Tester Display |
|---|
| MT Voltage Value |
| Accumulator Pressure |
While fully depressing the brake pedal 4 or 5 times, check that the MT voltage value is 10 V or more once or more.
Usually the MT voltage value is 0 V.
After confirming that the booster pump motor stops, check the accumulator pressure.
15 to 21 MPa
47210L
2.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Check auxiliary battery voltage.
11 to 14 V (while the ignition switch is off)
Set a pedal effort gauge, SST and connect the GTS.
| *a | Pedal Effort Gauge |
| *b | SST (LSPV Gauge) |
| *c | SST (No. 1 Nipple) |
Set a pedal effort gauge and SST.
Connect the GTS to the DLC3 with the ignition switch off, park (P) selected and parking brake applied.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Bleed air from SST (LSPV gauge).
Check operation without the brake booster.
Inspect and adjust the brake pedal height.
| *a | Fluid Level Support Line |
| *b | MIN Line |
Adjust the brake fluid level in the reservoir between MIN line and fluid level support line.
Turn the GTS on and enter the following menus: Chassis / Brake/EPB / Utility / ECB (Electronically Controlled Brake system) Utility.
| Tester Display |
|---|
| ECB Utility |
Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.
Perform "Motor Invalid" according to the display on the GTS.
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.
Check that the brake pedal is firm.
Enter the following menus: Chassis / Brake/EPB / Data List / Stroke Sensor and Stroke Sensor 2.
| Tester Display |
|---|
| Stroke Sensor |
| Stroke Sensor2 |
Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.
| Pedal Effort | Stroke Sensor
(V) |
Stroke Sensor 2
(V) |
Front Right Wheel Hydraulic Pressure | Rear Left Wheel Hydraulic Pressure |
|---|---|---|---|---|
| 200 N (20 kgf, 45.0 lbf) | 1.23 to 1.93 | 3.07 to 3.77 | 0.06 to 2.06 MPa (0.6 to 21.0 kgf/cm2, 9 to 299 psi) | 0.06 to 2.06 MPa (0.6 to 21.0 kgf/cm2, 9 to 299 psi) |
| 500 N (51 kgf, 112.4 lbf) | 1.42 to 2.12 | 2.88 to 3.58 | 2.09 to 4.09 MPa (21.3 to 41.7 kgf/cm2, 303 to 593 psi) | 2.09 to 4.09 MPa (21.3 to 41.7 kgf/cm2, 303 to 593 psi) |
| Pedal Effort | Stroke Sensor
(V) |
Stroke Sensor 2
(V) |
Front Left Wheel Hydraulic Pressure | Rear Right Wheel Hydraulic Pressure |
|---|---|---|---|---|
| 200 N (20 kgf, 45.0 lbf) | 1.23 to 1.93 | 3.07 to 3.77 | 0.06 to 2.06 MPa (0.6 to 21.0 kgf/cm2, 9 to 299 psi) | 0.06 to 2.06 MPa (0.6 to 21.0 kgf/cm2, 9 to 299 psi) |
| 500 N (51 kgf, 112.4 lbf) | 1.42 to 2.12 | 2.88 to 3.58 | 2.09 to 4.09 MPa (21.3 to 41.7 kgf/cm2, 303 to 593 psi) | 2.09 to 4.09 MPa (21.3 to 41.7 kgf/cm2, 303 to 593 psi) |
Remove the pedal effort gauge and SST, and bleed the brake system.
Enter the following menus: Chassis / Brake/EPB / Data List / Accumulator Pressure, and check the output pressure.
15 to 21 MPa
| Tester Display |
|---|
| Accumulator Pressure |
Clear the DTCs.
3.INSPECT STROKE SIMULATOR
Check auxiliary battery voltage.
11 to 14 V (while the ignition switch is off)
Connect the GTS and set a pedal effort gauge.
Set a pedal effort gauge.
Connect the GTS to the DLC3 with the ignition switch off, park (P) selected and parking brake applied.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Check operation with the brake booster.
Turn the ignition switch to ON.
Enter the following menus: Chassis / Brake/EPB / Data List / Stroke Sensor and Stroke Sensor 2.
| Tester Display |
|---|
| Stroke Sensor |
| Stroke Sensor2 |
Depress the brake pedal 4 or 5 times.
Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.
| Pedal Effort | Stroke Sensor
(V) |
Stroke Sensor 2
(V) |
|---|---|---|
| 50 N (5 kgf, 11.2 lbf) | 1.15 to 1.85 | 3.15 to 3.85 |
| 100 N (10 kgf, 22.5 lbf) | 1.30 to 2.00 | 3.00 to 3.70 |
| 150 N (15 kgf, 33.7 lbf) | 1.41 to 2.11 | 2.89 to 3.59 |