1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT
Remove front door scuff plate RH.
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Remove cowl side trim board RH.
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Turn back floor carpet.
Turn back dash panel insulator assembly.
Check the brake pedal height.
Inspect and adjust the brake pedal height with the tibia pad folded back.
Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.
| *1 | Brake Pedal Pad | - | - |
| *a | Brake Pedal Height | - | - |
|
Measuring Plane of Floor Panel | - | - |
157.8 to 173.8 mm (6.21 to 6.84 in.)
If the pedal height is not as specified, adjust the brake pedal height according to the procedure below.
| *1 | Stop Light Switch Assembly |
| *2 | Clevis Lock Nut |
| *3 | Floor Panel |
| *a | Brake Pedal Height |
Adjust the brake pedal height.
Remove the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Loosen the clevis lock nut.
Adjust the brake pedal height by turning the push rod.
157.8 to 173.8 mm (6.21 to 6.84 in.)
Tighten the clevis lock nut.
Install the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
Install the dash panel insulator assembly.
Install the floor carpet.
Install cowl side trim board RH.
Use the same procedure as for the LH side.
Install front door scuff plate RH.
Use the same procedure as for the LH side.
89510D
2.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY (for TMC Made)
Inspect the brake pedal stroke sensor assembly.
Connect the GTS to the DLC3 with the ignition switch off.
Turn the ignition switch to ON.
Turn the GTS on and enter the following menus: Chassis / Brake / Data List / Stroke Sensor.
| Tester Display |
|---|
| Stroke Sensor |
Read the stroke sensor value without the brake pedal depressed.
0.8 to 1.2 V
If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.
Adjust the brake pedal stroke sensor assembly.
Remove the No. 2 air duct.
Loosen the 2 nuts.
After turning the ignition switch to ON, do not depress the brake pedal until the nuts have been tightened.
Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.
0.8 to 1.2 V
Tighten the 2 nuts.
Turn the GTS off and turn the ignition switch off.
Disconnect the GTS.
Install the No. 2 air duct.
3.PERFORM INITIALIZATION AND CALIBRATION
4.INSPECT BRAKE PEDAL FREE PLAY
| *a | Brake Pedal Free Play |
Depress the brake pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.
1.0 to 6.0 mm (0.0394 to 0.236 in.)
If the pedal free play is not as specified, check the stop light switch clearance.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.
5.INSPECT BRAKE PEDAL RESERVE DISTANCE
Remove front door scuff plate RH.
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Remove cowl side trim board RH.
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Turn back floor carpet.
Turn back dash panel insulator assembly.
With the ignition switch ON (READY), depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.
| *1 | Brake Pedal Pad | - | - |
| *a | Brake Pedal Reserve Distance | - | - |
|
Measuring Plane of Floor Panel | - | - |
100 mm (3.94 in.) or more
84 mm (3.307 in.) or more
Install the dash panel insulator assembly.
Install the floor carpet.
Install cowl side trim board RH.
Use the same procedure as for the LH side.
Install front door scuff plate RH.
Use the same procedure as for the LH side.