| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority | Test Mode / Check Mode |
|---|---|---|---|---|---|---|---|
| B00D214 | Restraint System Malfunction Indicator 1 Circuit Short to Ground or Open | ·
The airbag sensor assembly detects a short to ground in the restraint system malfunction indicator 1 circuit when the airbag sensor assembly sends a passenger airbag indicator OFF signal to the passenger airbag ON indicator ·
The airbag sensor assembly detects an open in the restraint system malfunction indicator 1 circuit when the airbag sensor assembly sends a passenger airbag indicator OFF signal to the passenger airbag ON indicator ·
Telltale light assembly malfunction ·
Airbag sensor assembly malfunction |
·
Harness or connector ·
Telltale light assembly ·
Airbag sensor assembly |
Comes on | SRS Airbag | A | Does not apply to test/check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Inspect the fuses for circuits related to this system before performing the following procedure.
Turn the ignition switch to ON.
Check the passenger airbag ON indicator operation.
Refer to the normal condition of the passenger airbag ON indicator.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| Passenger airbag ON indicator is always on | A |
| Passenger airbag ON indicator is always off | B |
A
B
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Procedure1
Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the connectors from the airbag sensor assembly and telltale light assembly.
Procedure1
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Telltale Light Assembly) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H8,H14)Location & Routingewd_type=routing;type=c,c;code=H8,H14 Click Connector(H8)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telltale Light Assemblyewd_type=component;type=c;code=H8;pinno=3 Click Connector(H14)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Sensor Assemblyewd_type=component;type=c;code=H14;pinno=35 |
||
| H8-3 (PAON) or H14-35 (PAON) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Connect the connector to the telltale light assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
Check the passenger airbag ON indicator operation.
The passenger airbag ON indicator does not come on.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Procedure1
Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the connectors from the airbag sensor assembly and telltale light assembly.
Procedure1
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Telltale Light Assembly) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H8,H14)Location & Routingewd_type=routing;type=c,c;code=H8,H14 Click Connector(H8)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telltale Light Assemblyewd_type=component;type=c;code=H8;pinno=3 Click Connector(H14)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Sensor Assemblyewd_type=component;type=c;code=H14;pinno=35 |
||
| H8-3 (PAON) - H14-35 (PAON) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H8)Location & Routingewd_type=routing;type=c;code=H8 Click Connector(H8)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telltale Light Assemblyewd_type=component;type=c;code=H8;pinno=5 |
||
| H8-5 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
OK
NG
Pre-procedure1
Connect the connector to the telltale light assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *1 | Telltale Light Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Wire Harness |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Check the passenger airbag ON indicator according to the conditions in the table below.
| Terminal Connection | Switch Condition | Specified Condition |
|---|---|---|
| H14-35 (PAON) - Body ground | Ignition switch ON | Passenger airbag ON indicator comes on |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
OK
NG