Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY › from 2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443941 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B620273N01
6.344,2.25 6.677,2.25 false 6.5,0.208 6.865,0.208 false 6.5,0.625 6.823,0.625 false 5.167,3.417 5.75,3.417 true 1.896,0.5 2.313,0.5 false 6.281,0.042 6.563,0.396 0.281,0.354 18 false 1 6.292,0.469 6.573,0.823 0.281,0.354 18 false 2 6.719,2.104 7,2.458 0.281,0.354 18 false 3 5.802,3.25 6.083,3.604 0.281,0.354 18 false 4 2.594,0.344 2.875,0.698 0.281,0.354 18 false 5 1.552,0.198 1.865,0.396 0.313,0.198 10 false x3 2.469,3.406 2.781,3.604 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
3 REAR CONSOLE BOX ASSEMBLY 58910C - - -
4 FRONT FLOOR CARPET ASSEMBLY 58510D - - -
5 AIR BAG SENSOR ASSEMBLY 89170 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the center airbag sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system*1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B473126

Be sure to read Precaution thoroughly before servicing.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 58910C 3.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 58510D 4.SEPARATE FRONT FLOOR CARPET ASSEMBLY

a.
B620274C01
0,0 0,0 false
V113147

Separate in this direction - -



Hide 89170 5.REMOVE AIR BAG SENSOR ASSEMBLY

a.
B620238C05
1.323,0.802 0.323,0.802 true 0.115,0.688 0.427,0.844 0.313,0.156 10 false *a 4.615,0.073 4.896,0.427 0.281,0.354 18 false ii 0.167,0.063 0.448,0.417 0.281,0.354 18 false i 3.021,1.75 3.396,1.99 0.375,0.24 12 false *A 1.833,1.771 2.073,2 0.24,0.229 12 true *B
*A w/ Entry and Start System *B w/o Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B592995C02
0.458,0.115 0.74,0.469 0.281,0.354 18 false i 4.344,0.083 4.625,0.438 0.281,0.354 18 false ii
V113147

Remove in this direction (1)
V113148

Remove in this direction (2)


i.

Pull out each connector with its connector lock pushed to disconnect the 3 connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



ii.

Remove the 3 bolts and air bag sensor assembly.

NOTICE:

If the air bag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the air bag sensor assembly with a new one.