Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0438896 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B00DF12  Passenger Restraints Disable Switch Circuit Short to Battery  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority Test Mode / Check Mode
B00DF12 Passenger Restraints Disable Switch Circuit Short to Battery
·

The airbag sensor assembly detects a line short in the passenger restraints disable switch circuit for 2 seconds

·

The airbag sensor assembly detects a short to B+ in the passenger restraints disable switch circuit for 2 seconds

·

Airbag cut off switch cylinder sub-assembly malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

Airbag cut off switch cylinder sub-assembly

·

Airbag sensor assembly


Comes on SRS Airbag A Does not apply to test/check mode

WIRING DIAGRAM

B512690E13
4.854,2.979 5.479,3.177 0.625,0.198 10 false H14 4.844,3.146 6.583,3.542 1.74,0.396 10 false Airbag Sensor Assembly 0.542,2.823 1.177,3 0.635,0.177 10 false H15 0.542,2.99 3.552,3.396 3.01,0.406 10 false Airbag Cut Off Switch Cylinder Sub-assembly 2.219,1.115 2.802,1.448 0.583,0.333 10 false 2 1.729,1.115 2.313,1.448 0.583,0.333 10 false PMC+ 1.75,2.302 2.333,2.635 0.583,0.333 10 false PMC- 2.208,2.302 2.792,2.635 0.583,0.333 10 false 1 4.885,1.104 5.469,1.438 0.583,0.333 10 false MSW+ 4.635,1.104 5.219,1.438 0.583,0.333 10 false 22 4.885,2.302 5.469,2.635 0.583,0.333 10 false MSW- 4.635,2.302 5.219,2.635 0.583,0.333 10 false 21

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

a.

Check that the connectors are properly connected to the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS

Pre-procedure1

a.

Disconnect the connectors from the airbag sensor assembly and airbag cut off switch cylinder sub-assembly.


Procedure1

C422859C02
1.521,0.563 1.521,0.99 false 2.625,0.969 2.958,1.313 0.333,0.344 10 false *2 1.448,0.385 1.781,0.542 0.333,0.156 10 false *3 0.406,0.969 0.615,1.208 0.208,0.24 10 false *1
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Wire Harness


a.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK WIRE HARNESS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WIRE HARNESS
a.
C422878C01
0.729,2.167 1.083,2.417 0.354,0.25 1.24,2.802 1.583,2.385 true 2.188,2.802 1.854,2.385 true 1.635,1.104 1.635,0.771 false 0.417,0.615 0.667,0.833 0.25,0.219 10 false *1 2.75,0.615 3.083,0.917 0.333,0.302 10 false *2 1.583,1.146 1.896,1.385 0.313,0.24 10 false *3 0.625,1.646 1.042,1.896 0.417,0.25 10 false *a 1.073,2.833 1.583,3.083 0.51,0.25 10 false PMC- 2.104,2.833 2.667,3.083 0.563,0.25 10 false PMC+ 0.792,2.208 1.167,2.417 0.375,0.208 10 false H15 2.354,0.615 2.583,0.833 0.229,0.219 10 false A 1.979,0.615 2.167,0.833 0.188,0.219 10 false B 1.146,0.615 1.333,0.833 0.188,0.219 10 false C 0.771,0.615 0.917,0.833 0.146,0.219 10 false D
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H15)Location & Routing

Click Connector(H15)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Cut Off Switch Cylinder Sub-Assembly

H15-2 (PMC+) - Body ground Ignition switch ON Below 1 V
H15-1 (PMC-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H15)Location & Routing

Click Connector(H15)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Cut Off Switch Cylinder Sub-Assembly

H15-2 (PMC+) - H15-1 (PMC-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.
C422879C01
2.094,1 2.219,1.188 0.125,0.188 10 false A 1.938,1 2.083,1.271 0.146,0.271 10 false B 1.271,1.01 1.406,1.198 0.135,0.188 10 false C 0.927,1.01 1.042,1.229 0.115,0.219 10 false D 0.563,1.021 0.833,1.271 0.271,0.25 10 false *1 2.542,1.031 2.906,1.292 0.365,0.26 10 false *2
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC
5.CHECK DTC
a.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
Result:
Result Proceed to
B00DF12 is not output A
B00DF12 is output B


HINT:

Codes other than DTC B00DF12 may be output at this time, but they are not related to this check.




A

REPLACE AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

B