Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR GLASS › from 2021.07
RM3700E _59 Vehicle Exterior _092997 MIRROR (EXT) _0438350 OUTER REAR VIEW MIRROR GLASS A

MIRROR (EXT)  OUTER REAR VIEW MIRROR GLASS  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B603707N01
5.479,1.667 5.833,1.667 true 6.219,1.521 6.385,1.833 0.167,0.313 18 true 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 OUTER MIRROR 87961 (Click here) - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 87961 1.REMOVE OUTER MIRROR

a.
B603708C01
0.25,0.083 6.917,4.667 6.667,4.583 3.583,4.667 3.583,0.083 false 0.292,0.125 0.625,0.406 0.333,0.281 12 false *A 3.625,0.125 3.958,0.385 0.333,0.26 12 false *B 4.417,0.146 4.583,0.417 0.167,0.271 18 false i 6.385,0.542 6.542,0.833 0.156,0.292 18 true ii 5,1.458 5.219,1.729 0.219,0.271 18 true iii 2.844,3.635 3.094,3.917 0.25,0.281 18 true iv 1.51,2.635 1.844,2.917 0.333,0.281 18 false v 6.281,3.635 6.531,3.917 0.25,0.281 18 true iv 4.948,2.635 5.281,2.917 0.333,0.281 18 false v 0.99,0.146 1.167,0.417 0.177,0.271 18 false i 1.583,1.479 1.802,1.75 0.219,0.271 18 true iii 2.958,0.542 3.125,0.833 0.167,0.292 18 true ii
*A for TMC Made *B for TMMF Made
V100135

Push - -


i.

Apply protective tape to the area as shown in the illustration.


ii.

Push the upper part of the mirror surface and tilt it.

NOTICE:

Do not push the outer mirror with excessive force. Doing so may break the mirror surface.



iii.

Using a moulding remover D, disengage the claws on the lower part of the outer mirror.


iv.

Push the lower part of the mirror surface and tilt it.

NOTICE:
·

Do not push the outer mirror with excessive force. Doing so may break the mirror surface.

·

If excessive force is used when pressing down the mirror surface, the claws will engage again.




v.

Using a moulding remover D, disengage the claws on the upper part of the outer mirror to remove the outer mirror.



b.

w/ Blind Spot Monitor System:

B603709C01
0.25,0.104 0.583,0.365 0.333,0.26 12 false *A 3.667,0.104 4.052,0.333 0.385,0.229 12 false *B 3.906,0.042 4.188,0.396 0.281,0.354 18 false i 0.5,0.052 0.781,0.406 0.281,0.354 18 false i
*A for TMC Made *B for TMMF Made


i.

Disconnect the connector.



c.

w/ Mirror Heater:

B603710C01
0.25,0.104 0.583,0.365 0.333,0.26 12 false *A 3.667,0.104 4.052,0.333 0.385,0.229 12 false *B 3.906,0.042 4.188,0.396 0.281,0.354 18 false i 0.5,0.052 0.781,0.406 0.281,0.354 18 false i
*A for TMC Made *B for TMMF Made


i.

Disconnect each connector.