Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › AIR FUEL RATIO SENSOR (for Sensor 2) › from 2021.07
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442044 AIR FUEL RATIO SENSOR(for Sensor 2) A

M15A-FXE ENGINE CONTROL  AIR FUEL RATIO SENSOR(for Sensor 2)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A485870N01
0.167,0.167 7,2.583 6.833,2.417 1.75,2.052 1.75,1.719 false 4.885,2.104 4.885,1.771 false 6.469,0.833 6.135,0.833 false 3.5,2.583 3.5,0.167 false 1.677,2.083 1.958,2.438 0.281,0.354 18 false 1 4.823,2.115 5.104,2.469 0.281,0.354 18 false 1 6.542,0.667 6.823,1.021 0.281,0.354 18 false 2 6.677,1.583 6.99,1.781 0.313,0.198 10 false x2 5.802,1.958 6.115,2.156 0.313,0.198 10 false x2 4.24,1.875 4.552,2.073 0.313,0.198 10 false x2 2.604,1.76 2.917,1.958 0.313,0.198 10 false x2 1.031,1.854 1.344,2.052 0.313,0.198 10 false x2 0.208,0.198 0.583,0.438 0.375,0.24 12 false *A 3.563,0.188 3.938,0.427 0.375,0.24 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
2 CENTER NO. 1 FLOOR BRACE 57543C - - -

*A for TMC MADE *B for TMMF MADE

A459229N03
4.813,3 5.24,3 false 4.188,3.375 4.188,3.708 false 4.115,3.74 4.396,4.094 0.281,0.354 18 false 3 5.719,2.865 6,3.219 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

3 WIRE HARNESS CLAMP BRACKET - - - -
4 NO. 2 AIR FUEL RATIO SENSOR 89467C (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 2 air fuel ratio sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of air fuel ratio sensor (sensor 2) Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Gas leak from exhaust system is repaired

CAUTION:
·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 51447D 1.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 57543C 2.REMOVE CENTER NO. 1 FLOOR BRACE (for TMMF Made)

Hide 3.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A458739


Hide 89467C 4.REMOVE NO. 2 AIR FUEL RATIO SENSOR

a.
A458740N01
6,0.885 5.656,0.531 true 0.49,0.094 0.875,0.396 0.385,0.302 18 true i, ii 4.344,0.083 4.729,0.385 0.385,0.302 18 true iii 5.865,0.885 6.188,1.052 0.323,0.167 10 true SST

i.

Disconnect the No. 2 air fuel ratio sensor connector.


ii.

Disengage the 2 wire harness clamp.


iii.

Using SST, remove the No. 2 air fuel ratio sensor from the front exhaust pipe assembly (TWC: Rear Catalyst).

SST
09224-00012  

NOTICE:

If the No. 2 air fuel ratio sensor has been struck or dropped, replace it.