Home › Engine / Hybrid System › STOP AND START › ENGINE STOP AND START ECU › from 2021.07
RM3700E _51 Engine / Hybrid System _105429 STOP AND START _0482030 ENGINE STOP AND START ECU A

STOP AND START  ENGINE STOP AND START ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A485878N01
3.677,1 4.01,1 false 5.469,3.552 5.802,3.552 false 6.5,0.198 6.833,0.198 false 6.323,0.042 6.604,0.396 0.281,0.354 18 false 1 4.073,0.823 4.375,1.188 0.302,0.365 18 false 2 6.146,3.417 6.448,3.781 0.302,0.365 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 READ NUMBER OF STARTER OPERATIONS - (Click here) - -
2 INTEGRATION ECU BOX RH - - - -
3 ENGINE STOP AND START ECU 89261A (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed, or replaced during the engine stop and start ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Replacement of Engine stop and start ECU
1.

Upload the number of starter operations

2.

Reset air conditioning information

3.

Learning air conditioning information

4.

Clear the zero point calibration data

5.

Perform zero point calibration of the deceleration sensor

6.

Check the oil pump with solenoid assembly


Stop and start system (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. READ NUMBER OF STARTER OPERATIONS

Z101186

Click here(Click here)

Hide 82877 2.REMOVE INTEGRATION ECU BOX RH

Hide 89261A 3.REMOVE ENGINE STOP AND START ECU

a.
A485890N01
0.427,0.052 0.708,0.406 0.281,0.354 18 false i

i.

Disengage the 2 claws and remove the engine stop and start ECU from the ECU integration box RH.

NOTICE:
·

If the ECU integration box RH is deformed or damaged, replace it.

·

Do not bend the 2 claws more than necessary.