Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2021.07
RM3700E _51 Engine / Hybrid System _105429 STOP AND START _0482038 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Neutral Position Switch Circuit  


DESCRIPTION

The neutral position switch detects whether the shift lever is in neutral. When the shift lever in any position other than neutral, stop and start control is prohibited.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

For wire harness and connector inspection procedures and precautions, refer to "General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE"


PROCEDURE

1.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Enter the following menus.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 392 202

b.

Read the value when the shift lever is in neutral and any other position.

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever is in neutral ON
Shift lever is in any position other than neutral OFF



Result:
Proceed to
OK
NG



OK

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the D44 neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A67,D44)Location & Routing

Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

Click Connector(D44)Engine Compartment>Engine Wire>Neutral Position Switch

A67-26 (TMVC) - D44-1 (W1) Always Below 1 Ω
A67-25 (TME2) - D44-3 (F+) Always Below 1 Ω
A67-8 (TMN) - D44-2 (TMN) Always Below 1 Ω
A67-26 (TMVC) - Body ground and other terminals Always 10 kΩ or higher
D44-1 (W1) - Body ground and other terminals Always 10 kΩ or higher
A67-25 (TME2) - Body ground and other terminals Always 10 kΩ or higher
D44-3 (F+) - Body ground and other terminals Always 10 kΩ or higher
A67-8 (TMN) - Body ground and other terminals Always 10 kΩ or higher
D44-2 (TMN) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)
A456121C41
3.26,0.094 3.646,0.365 0.385,0.271 3.063,0.948 3.75,1.458 true 3.073,0.833 2.75,1.49 true 0.708,0.094 1.021,0.292 0.313,0.198 10 false *a 3.74,1.5 4.354,1.698 0.615,0.198 10 false TME2 2.646,1.5 3.26,1.698 0.615,0.198 10 false TMN 3.323,0.135 3.938,0.333 0.615,0.198 10 false A67
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A67)Location & Routing

Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

A67-8 (TMN) - A67-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V



Result:
Proceed to
OK
NG



OK

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE NEUTRAL POSITION SENSOR (NEUTRAL POSITION SWITCH)