Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2021.07
RM3700E _51 Engine / Hybrid System _105429 STOP AND START _0482038 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P085011  Park/Neutral Switch Circuit Short to Ground  P085015  Park/Neutral Switch Circuit Short to Battery or Open  


DESCRIPTION

The engine stop and start ECU detects a malfunction by comparing the shift position signal with the neutral position switch signal input state. If a malfunction is detected, the engine stop and start ECU blinks the stop and start cancel indicator light, prohibits the stop and start control and stores DTC P085011 or P085015.


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory DTC Output from Priority Note
P085011 Park/Neutral Switch Circuit Short to Ground The following condition continues for 1 second or more (1 trip detection logic)
·

Short in neutral position switch circuit.


·

Neutral position switch

·

Engine stop and start ECU

·

Wire harness or connector


Blinking DTC stored Stop and Start A SAE Code: P0851
P085015 Park/Neutral Switch Circuit Short to Battery or Open The following condition continues for 1 second or more (1 trip detection logic)
·

Open or short in neutral position switch circuit.


·

Neutral position switch

·

Engine stop and start ECU

·

Wire harness or connector


Blinking DTC stored Stop and Start A SAE Code: P0852

WIRING DIAGRAM

A382306E17
0.979,2.052 1.292,2.25 0.313,0.198 10 false IC 2.333,1.104 2.646,1.302 0.313,0.198 10 false W1 2.25,1.958 2.615,2.156 0.365,0.198 10 false TMN 2.365,2.844 2.677,3.042 0.313,0.198 10 false F+ 0.792,3.469 1.104,3.667 0.313,0.198 10 false D44 0.792,3.625 2.5,3.906 1.708,0.281 10 false Neutral Position Switch 2.677,1.104 2.99,1.302 0.313,0.198 10 false 1 2.688,1.958 3,2.156 0.313,0.198 10 false 2 2.677,2.844 2.99,3.042 0.313,0.198 10 false 3 4.865,1.104 5.177,1.302 0.313,0.198 10 false 26 4.948,1.969 5.26,2.167 0.313,0.198 10 false 8 4.885,2.854 5.198,3.052 0.313,0.198 10 false 25 5.177,1.104 5.802,1.302 0.625,0.198 10 false TMVC 5.177,1.979 5.823,2.219 0.646,0.24 10 false TMN 5.177,2.865 5.615,3.073 0.438,0.208 10 false TME2 5.167,3.771 5.604,3.979 0.438,0.208 10 false A67 5.167,3.927 6.927,4.323 1.76,0.396 10 false Engine Stop and Start ECU 6.125,0.854 6.563,1.063 0.438,0.208 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the ECM is replaced on a vehicle with a non-specified auxiliary battery, it is necessary to perform auxiliary battery type switching.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

For wire harness and connector inspection procedures and precautions, refer toGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (NEUTRAL SWITCH)

Pre-procedure1

a.

Enter the following menus.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 392 202

Procedure1

b.

Read the value when the shift lever is in neutral and any other position.

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in neutral ON
Neutral Switch Shift lever in any position other than neutral OFF



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)

Pre-procedure1

a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the D44 neutral position switch connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A67,D44)Location & Routing

Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

Click Connector(D44)Engine Compartment>Engine Wire>Neutral Position Switch

A67-26 (TMVC) - D44-1 (W1) Always Below 1 Ω
A67-25 (TME2) - D44-3 (F+) Always Below 1 Ω
A67-8 (TMN) - D44-2 (TMN) Always Below 1 Ω
A67-26 (TMVC) - Body ground and other terminals Always 10 kΩ or higher
D44-1 (W1) - Body ground and other terminals Always 10 kΩ or higher
A67-25 (TME2) - Body ground and other terminals Always 10 kΩ or higher
D44-3 (F+) - Body ground and other terminals Always 10 kΩ or higher
A67-8 (TMN) - Body ground and other terminals Always 10 kΩ or higher
D44-2 (TMN) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)
a.

Measure the voltage according to the value(s) in the table below.

A387803C19
3.219,0.083 3.635,0.333 0.417,0.25 3.75,1.5 3.073,0.938 true 2.479,1.5 3.063,0.833 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 3.313,0.125 3.771,0.323 0.458,0.198 10 false A67 3.615,1.5 4.229,1.698 0.615,0.198 10 false TME2 2.333,1.5 2.948,1.698 0.615,0.198 10 false TMN
*a Component with harness connected
(Engine Stop and Start ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A67)Location & Routing

Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECU

A67-8 (TMN) - A67-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
A67-8 (TMN) - A67-25 (TME2) Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V



Result:
Result
OK
NG



OK

NG