If the engine stop and start ECU receives the off signal from the ignition or starter switch assembly*1 or certification ECU (smart key ECU assembly)*2 when communication with the ECM is normal, the engine stop and start ECU will output DTC P253014.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|---|
| P253014 | Ignition Switch Circuit Short to Ground or Open | All of the following conditions are met for 10 seconds or more (1 trip detection logic):
·
Ignition switch off signal is input. ·
Communication with the ECM is normal. ·
Ignition switch (communication) ON |
·
Wire harness or connector ·
EFI-MAIN NO. 1 relay ·
IGP relay ·
Power distribution box assembly (IGR-NO. 1 relay)*1 ·
Ignition or starter switch assembly*2 ·
Certification ECU (Smart key ECU assembly)*1 ·
Engine stop and start ECU |
Blinks | DTC stored | Stop and Start | A | SAE Code: P2531 |
*1: w/ Entry and Start System
*2: w/o Entry and Start System
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the auxiliary battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Auxiliary Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the auxiliary battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item "Status of Auxiliary Battery Charge Control" cannot be checked, charge the auxiliary battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Clear the DTCs.
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Keep the engine stopped by stop and start control for 1 second or more.
Depress the clutch pedal and start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that the auxiliary battery voltage is low.
Check that DTCs are not output.
STOP AND START SYSTEM OPERATION CHECK
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the ECM is replaced on a vehicle with a non-specified auxiliary battery, it is necessary to perform auxiliary battery type switching.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA
For wire harness and connector inspection procedures and precautions, refer to "General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE"
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR
Enter the following menus.
| Tester Display |
|---|
| IG Switch |
Read the value displayed on the GTS.
| Tester Display | Result | Proceed to |
|---|---|---|
| IG Switch | ON | A |
| IG Switch | OFF | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
| *a | Component with harness connected
(Engine Stop and Start ECU) |
- | - |
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H43)Location & Routingewd_type=routing;type=c;code=H43 Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECUewd_type=component;type=c;code=H43;pinno=18 |
||
| H43-18 (IGP) - Body ground | Ignition switch ON | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
| *a | Component with harness connected
(Engine Stop and Start ECU) |
- | - |
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A67)Location & Routingewd_type=routing;type=c;code=A67 Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECUewd_type=component;type=c;code=A67;pinno=1 |
||
| A67-1 (+B) - Body ground | Ignition switch ON | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY>REMOVAL
NG
Pre-procedure1
Disconnect the A67 engine stop and start ECU connector.
Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.
Procedure1
Measure the resistance according to the value(s) in the table below.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A67)Location & Routingewd_type=routing;type=c;code=A67 Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECUewd_type=component;type=c;code=A67;pinno=1 |
||
| A67-1 (+B) - 3 (EFI-MAIN NO. 1 relay holder) | Always | Below 1 Ω |
| A67-1 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| 3 (EFI-MAIN NO. 1 relay holder) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Inspect the EFI-MAIN NO. 1 relay.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI-MAIN NO. 1 relay holder) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
| *1 | Component without harness connected
(No. 1 Engine Room Relay Block) |
| *a | EFI-MAIN NO. 1 Relay Holder |
Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (EFI-MAIN NO. 1 relay holder) - Body ground | Always | 9.5 to 14 V |
| 5 (EFI-MAIN NO. 1 relay holder) - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Disconnect the H43 engine stop and start ECU connector.
Disconnect the 4B power distribution box assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H43)Location & Routingewd_type=routing;type=c;code=H43 Click Connector(H43)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Stop and Start ECUewd_type=component;type=c;code=H43;pinno=21 |
||
| H43-21 (IGR) - 4B-10 | Always | Below 1 Ω |
| H43-21 (IGR) - Body ground and other terminals | Always | 10 kΩ or higher |
| 4B-10 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Check the vehicle specification
| Result | Proceed to |
|---|---|
| w/ Entry and Start System | A |
| w/o Entry and Start System | B |
A
B
Pre-procedure1
Remove the power distribution box assembly.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-10 (voltmeter positive (+) lead) - 4B-4 (voltmeter negative (-) lead) | Auxiliary battery voltage not applied to terminals 4C-17 (auxiliary battery positive (+)) and 4C-41 (auxiliary battery negative (-)) | Below 1 V |
| 4B-10 (voltmeter positive (+) lead) - 4B-4 (voltmeter negative (-) lead) | Auxiliary battery applied to terminals 4C-17 (auxiliary battery positive (+)) and 4C-41 (auxiliary battery negative (-)) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Disconnect the 4C power distribution box assembly connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-41 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG