Home › Vehicle Exterior › WINDOW / GLASS › ROOF WINDOW FIX GLASS › from 2021.07
RM3700E _59 Vehicle Exterior _092998 WINDOW / GLASS _0482096 ROOF WINDOW FIX GLASS A

WINDOW / GLASS  ROOF WINDOW FIX GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

COMPNENTS (INSTALLATION)
B621649N02
1.333,1.917 6,3.667 4.667,1.75 1.333,0.167 6,1.833 4.667,1.667 4.875,0.948 5.25,0.948 false 4.896,2.677 5.25,2.677 false 6.583,0.167 6.875,0.167 false 5.719,0.729 6,1.083 0.281,0.354 18 false 2 5.74,2.49 6.021,2.844 0.281,0.354 18 false 3 1.417,0.219 1.792,0.458 0.375,0.24 12 false *A 1.417,1.979 1.792,2.219 0.375,0.24 12 false *B 6.094,0.021 6.677,0.344 0.583,0.323 18 false 1, 4 5.615,2.542 5.771,2.74 0.156,0.198 10 false ● 5.594,0.802 5.75,1 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CLEAN NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY 63201M (Click here) - -
2 NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY 63201M (Click here) - -
3 NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY 63201M (Click here) - -
4 INSPECT FOR LEAK - - - -

*A w/ Roof Rack *B w/o Roof Rack
● Non-reusable part - -

B623360N01
0.167,2 7,3.667 6.833,1.667 1.667,3.167 1.667,2.833 false 1.896,0.958 1.563,0.958 false 5.583,3.167 5.583,2.833 false 3.583,3.667 3.583,2 false 5.531,3.177 5.813,3.531 0.281,0.354 18 false 6 1.594,3.177 1.875,3.531 0.281,0.354 18 false 5 1.406,0.792 1.688,1.146 0.281,0.354 18 false 7 3.646,2.052 4.021,2.292 0.375,0.24 12 false *B 0.208,2.042 0.583,2.281 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

5 REAR ROOF DRIP SIDE FINISH MOULDING 75554A - - -
6 ROOF RACK ASSEMBLY 63470B - - -
7 SUNSHADE TRIM BRACKET SUB-ASSEMBLY 63306 - - -

*A w/o Roof Rack *B w/ Roof Rack

PROCEDURE

Hide 63201M 1.CLEAN NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY

a.
B620919N01
0.427,0.073 0.708,0.427 0.281,0.354 18 false i

i.

Clean the outer circumference of the No. 1 roof window glass sub-assembly with non-residue solvent.

NOTICE:
·

Do not touch the No. 1 roof window glass sub-assembly surface after cleaning it.

·

Be careful not to damage the glass.





Hide 63201M 2.INSTALL NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY (w/ Roof Rack)

a.
B619121C01
2.24,0.781 2.406,0.948 false 5.792,0.802 5.958,0.969 false 6.031,0.865 6.344,1.021 0.313,0.156 10 false *a 2.479,0.844 2.792,1 0.313,0.156 10 false *a 0.427,0.063 0.708,0.417 0.281,0.354 18 false i
*a Roof Panel - -
V100155

Adhesive - -


i.

Clean and shape the contact surface of the roof panel.

1. Using a knife, cut away excess adhesive on the contact surface of the roof panel as shown in the illustration.

NOTICE:

Leave as much adhesive on the roof panel as possible.


2. Clean the contact surface of the roof panel with a piece of cloth saturated with non-residue solvent.



b.
B620921C01
3.042,0.646 2.5,0.333 2.5,0.333 2.792,0.344 true 2.302,0.229 2.615,0.385 0.313,0.156 10 false *a 0.396,0.063 0.625,0.406 0.229,0.344 18 false i
*a Matchmarks - -


i.

Position the No. 1 roof window glass sub-assembly.

1. Using suction cups, place the No. 1 roof window glass sub-assembly in the correct position.

2. Check that the whole contact surface of the No.1 roof window glass sub-assembly rim is perfectly even.

3. Align the matchmarks on the No. 1 roof window glass sub-assembly and vehicle body.

NOTICE:

Check that the roof window clips are engaged to the vehicle body correctly.


4. Using suction cups, remove the No. 1 roof window glass sub-assembly.

5. Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.




c.
B619117C01
0.729,0.083 1.042,0.24 0.313,0.156 10 false *a 1.927,2.375 2.323,2.594 0.396,0.219 10 false B-B 0.25,2.375 0.667,2.583 0.417,0.208 10 false A-A 1.01,0.25 1.323,0.406 0.313,0.156 10 false A 1.042,1.198 1.177,1.365 0.135,0.167 10 false B 2.573,1.719 2.708,1.885 0.135,0.167 10 false C 3.104,1.667 3.24,1.833 0.135,0.167 10 false D 1.417,0.25 1.729,0.406 0.313,0.156 10 false A 1.448,1.146 1.583,1.313 0.135,0.167 10 true B 2.531,1.302 2.667,1.469 0.135,0.167 10 true C 3.073,1.25 3.208,1.417 0.135,0.167 10 true D 3.958,0.208 4.271,0.365 0.313,0.156 10 false E 4.365,0.208 4.677,0.365 0.313,0.156 10 false E 5.594,0.583 5.99,0.802 0.396,0.219 10 false C-C 4.427,2.375 4.823,2.594 0.396,0.219 10 false D-D 6.188,2.385 6.583,2.604 0.396,0.219 10 false E-E 0.833,2.667 1,2.833 0.167,0.167 10 false a 2.333,2.563 2.5,2.729 0.167,0.167 10 false b 5.688,0.802 5.854,0.969 0.167,0.167 10 false c 4.51,2.604 4.677,2.771 0.167,0.167 10 false d 6.281,2.615 6.448,2.781 0.167,0.167 10 false e 0.438,0.063 0.719,0.417 0.281,0.354 18 false i
*a Back Side of No. 1 Roof Window Glass Sub-assembly - -
V100155

Primer G - -


i.

Using a brush or sponge, coat the adhesive application area with primer G.

Standard:
Area Specified Condition Area Specified Condition
a 30.6 mm (1.20 in.) or more b 21.7 mm (0.854 in.) or more
c 16.7 mm (0.657 in.) or more d 20.0 mm (0.787 in.) or more
e 20.0 mm (0.787 in.) or more - -


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.




d.
B622655C01
3.115,0.49 3.25,0.625 false 3.281,0.51 3.594,0.667 0.313,0.156 10 false *a 2.563,0.594 2.719,0.75 0.156,0.156 10 false a 2.75,0.906 2.906,1.063 0.156,0.156 10 false b 3.042,0.854 3.198,1.01 0.156,0.156 10 false b 3.219,1.25 3.375,1.406 0.156,0.156 10 false a 0.448,0.083 0.729,0.438 0.281,0.354 18 false i
*a Cartridge Nozzle - -
V100155

Adhesive - -


i.

Apply adhesive to the No.1 roof window glass sub-assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


1. Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition Area Specified Condition
a 12 to 15 mm (0.472 to 0.591 in.) b 8.0 to 11 mm (0.315 to 0.433 in.)


2. Load the sealer gun with the cartridge.



e.
B605889C01
0.906,0.24 1.063,0.406 0.156,0.167 10 false A 0.167,2.167 0.583,2.333 0.417,0.167 10 false A-A 1.323,0.229 1.479,0.396 0.156,0.167 10 false A 3.844,0.198 4,0.365 0.156,0.167 10 false E 4.26,0.208 4.417,0.375 0.156,0.167 10 false E 0.938,1.208 1.094,1.375 0.156,0.167 10 false B 1.344,1.135 1.5,1.302 0.156,0.167 10 true B 2.469,1.708 2.625,1.875 0.156,0.167 10 false C 2.417,1.313 2.573,1.479 0.156,0.167 10 true C 2.99,1.667 3.146,1.833 0.156,0.167 10 false D 2.969,1.25 3.125,1.417 0.156,0.167 10 true D 1.833,2.167 2.25,2.333 0.417,0.167 10 false B-B 4.5,2.167 4.917,2.333 0.417,0.167 10 false D-D 5.698,0.5 6.115,0.667 0.417,0.167 10 false C-C 6.229,2.167 6.646,2.333 0.417,0.167 10 false E-E 0.771,2.292 0.927,2.458 0.156,0.167 10 false a 0.958,2.573 1.115,2.74 0.156,0.167 10 false b 2.26,2.458 2.417,2.625 0.156,0.167 10 false c 5.771,0.719 5.927,0.885 0.156,0.167 10 false d 4.594,2.542 4.75,2.708 0.156,0.167 10 false e 6.323,2.458 6.479,2.625 0.156,0.167 10 false f 0.667,0.083 0.823,0.25 0.156,0.167 10 false *a 0.396,0.021 0.677,0.375 0.281,0.354 18 false i
*a Back Side of No. 1 Roof Window Glass Sub-assembly - -
V100155

Adhesive Application Area - -


i.

Apply adhesive to the No. 1 roof window glass sub-assembly as shown in the illustration.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


Standard:
Area Specified Condition Area Specified Condition
a 14.5 mm (0.571 in.) b 9.1 mm (0.358 in.)
c 14.7 mm (0.579 in.) d 9.7 mm (0.382 in.)
e 13.0 mm (0.512 in.) f 13.0 mm (0.512 in.)




f.
B620922C01
3.021,0.625 2.51,0.333 2.51,0.333 2.823,0.385 true 0.406,0.063 0.688,0.417 0.281,0.354 18 false i 2.302,0.219 2.615,0.417 0.313,0.198 10 false *a
*a Matchmarks - -


i.

Install the No. 1 roof window glass sub-assembly.

1. Using suction cups, position the No. 1 roof window glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the roof window clips are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and No. 1 roof window glass sub-assembly.



2. Lightly press the outer surface of the No. 1 roof window glass sub-assembly to ensure a close fit and engage the roof window clips.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.


3. Using a scraper, remove any excess or protruding adhesive.

4. Hold the No. 1 roof window glass sub-assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




Hide 63201M 3.INSTALL NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY (w/o Roof Rack)

a.
B619121C01
2.24,0.781 2.406,0.948 false 5.792,0.802 5.958,0.969 false 6.031,0.865 6.344,1.021 0.313,0.156 10 false *a 2.479,0.844 2.792,1 0.313,0.156 10 false *a 0.427,0.063 0.708,0.417 0.281,0.354 18 false i
*a Roof Panel - -
V100155

Adhesive - -


i.

Clean and shape the contact surface of the roof panel.

1. Using a knife, cut away excess adhesive on the contact surface of the roof panel as shown in the illustration.

NOTICE:

Leave as much adhesive on the roof panel as possible.


2. Clean the contact surface of the roof panel with a piece of cloth saturated with non-residue solvent.



b.
B620923C01
3.042,0.646 2.5,0.333 2.5,0.333 2.792,0.344 true 2.302,0.229 2.615,0.385 0.313,0.156 10 false *a 0.406,0.073 0.688,0.427 0.281,0.354 18 false i
*a Matchmarks - -


i.

Position the No. 1 roof window glass sub-assembly.

1. Using suction cups, place the No. 1 roof window glass sub-assembly in the correct position.

2. Check that the whole contact surface of the No.1 roof window glass sub-assembly rim is perfectly even.

3. Align the matchmarks on the No. 1 roof window glass sub-assembly and vehicle body.

NOTICE:

Check that the roof window clips are engaged to the vehicle body correctly.


4. Using suction cups, remove the No. 1 roof window glass sub-assembly.

5. Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.




c.
B620944C01
1.333,0.198 1.583,0.396 0.25,0.198 10 false *a 1.792,0.333 1.958,0.531 0.167,0.198 10 false A 2.198,0.344 2.333,0.521 0.135,0.177 10 true A 4.792,0.344 4.927,0.521 0.135,0.177 10 true D 5.208,0.333 5.375,0.531 0.167,0.198 10 false D 3.844,1.615 3.979,1.792 0.135,0.177 10 true C 3.875,2.01 4.01,2.188 0.135,0.177 10 false C 0.792,2.333 1.125,2.5 0.333,0.167 10 false A-A 2.656,2.333 2.99,2.5 0.333,0.167 10 false B-B 4.771,2.333 5.104,2.5 0.333,0.167 10 false C-C 0.844,2.594 1.094,2.792 0.25,0.198 10 false a 2.708,2.542 2.958,2.74 0.25,0.198 10 false b 4.854,2.604 5.104,2.802 0.25,0.198 10 false c 2.208,1.188 2.344,1.365 0.135,0.177 10 true B 1.823,1.292 1.958,1.469 0.135,0.177 10 false B 6.385,2.333 6.719,2.5 0.333,0.167 10 false D-D 6.458,2.604 6.708,2.802 0.25,0.198 10 false d 0.438,0.063 0.792,0.469 0.354,0.406 18 false i
*a Back Side of No. 1 Roof Window Glass Sub-assembly - -
V100155

Primer G - -


i.

Using a brush or sponge, coat the adhesive application area with primer G.

Standard:
Area Specified Condition Area Specified Condition
a 30.6 mm (1.20 in.) or more b 21.7 mm (0.854 in.) or more
c 20.0 mm (0.787 in.) or more d 20.0 mm (0.787 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.




d.
B622655C01
3.115,0.49 3.25,0.625 false 3.281,0.51 3.594,0.667 0.313,0.156 10 false *a 2.563,0.594 2.719,0.75 0.156,0.156 10 false a 2.75,0.906 2.906,1.063 0.156,0.156 10 false b 3.042,0.854 3.198,1.01 0.156,0.156 10 false b 3.219,1.25 3.375,1.406 0.156,0.156 10 false a 0.448,0.083 0.729,0.438 0.281,0.354 18 false i
*a Cartridge Nozzle - -
V100155

Adhesive - -


i.

Apply adhesive to the No.1 roof window glass sub-assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


1. Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition Area Specified Condition
a 12 to 15 mm (0.472 to 0.591 in.) b 8.0 to 11 mm (0.315 to 0.433 in.)


2. Load the sealer gun with the cartridge.



e.
B622656C01
1.333,0.198 1.583,0.396 0.25,0.198 10 false *a 1.792,0.333 1.958,0.531 0.167,0.198 10 false A 2.198,0.344 2.333,0.521 0.135,0.177 10 true A 4.792,0.344 4.927,0.521 0.135,0.177 10 true D 5.208,0.333 5.375,0.531 0.167,0.198 10 false D 3.844,1.615 3.979,1.792 0.135,0.177 10 true C 3.875,2.01 4.01,2.188 0.135,0.177 10 false C 0.26,2.333 0.594,2.5 0.333,0.167 10 false A-A 2.198,2.333 2.531,2.5 0.333,0.167 10 false B-B 4.167,2.333 4.5,2.5 0.333,0.167 10 false C-C 0.927,2.396 1.177,2.594 0.25,0.198 10 false a 1.135,2.688 1.385,2.885 0.25,0.198 10 false b 2.76,2.479 3.01,2.677 0.25,0.198 10 false c 2.208,1.188 2.344,1.365 0.135,0.177 10 true B 1.823,1.292 1.958,1.469 0.135,0.177 10 false B 5.75,2.333 6.083,2.5 0.333,0.167 10 false D-D 6.469,2.563 6.719,2.76 0.25,0.198 10 false e 4.917,2.604 5.167,2.802 0.25,0.198 10 false d 0.438,0.052 0.719,0.406 0.281,0.354 18 false i
*a Back Side of No. 1 Roof Window Glass Sub-assembly - -
V100155

Adhesive Application Area - -


i.

Apply adhesive to the No. 1 roof window glass sub-assembly as shown in the illustration.

Standard:
Area Specified Condition Area Specified Condition
a 14.5 mm (0.571 in.) b 9.1 mm (0.358 in.)
c 14.7 mm (0.579 in.) d 13.0 mm (0.512 in.)
e 13.0 mm (0.512 in.) - -




f.
B620924C01
3.021,0.625 2.51,0.333 2.51,0.333 2.823,0.385 true 0.406,0.063 0.688,0.417 0.281,0.354 18 false i 2.302,0.219 2.615,0.417 0.313,0.198 10 false *a
*a Matchmarks - -


i.

Install the No. 1 roof window glass sub-assembly.

1. Using suction cups, position the No. 1 roof window glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the roof window clips are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and No. 1 roof window glass sub-assembly.



2. Lightly press the outer surface of the No. 1 roof window glass sub-assembly to ensure a close fit and engage the roof window clips.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.


3. Using a scraper, remove any excess or protruding adhesive.

4. Hold the No. 1 roof window glass sub-assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




Hide 4.INSPECT FOR LEAK

a.
E444338N01
0.344,0.042 0.625,0.396 0.281,0.354 18 false i

i.

Inspect for leaks by the below procedure.

1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

2. If water leaks into the cabin, allow the water to dry and add adhesive.

3. Remove the protective tape.



Hide 75554A 5.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING

Hide 63470B 6.INSTALL ROOF RACK ASSEMBLY (w/ Roof Rack)

Hide 63306 7.INSTALL SUNSHADE TRIM BRACKET SUB-ASSEMBLY