Home › Vehicle Exterior › ACOUSTIC VEHICLE ALERTING SYSTEM › VEHICLE APPROACHING SPEAKER ECU › from 2021.07
RM3700E _59 Vehicle Exterior _105446 ACOUSTIC VEHICLE ALERTING SYSTEM _0482097 VEHICLE APPROACHING SPEAKER ECU A

ACOUSTIC VEHICLE ALERTING SYSTEM  VEHICLE APPROACHING SPEAKER ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E460303N03
0.083,0.167 3.5,2.5 3.417,2.333 2.063,1.333 2.396,1.333 false 0.375,1.271 0.708,1.271 false 1.771,2.5 1.771,0.167 false 2.052,2.917 2.385,2.917 false 1.865,1.167 2.146,1.521 0.281,0.354 18 false 2 0.198,1.115 0.479,1.469 0.281,0.354 18 false 1 1.844,2.75 2.125,3.104 0.281,0.354 18 false 3 0.125,0.177 0.5,0.417 0.375,0.24 12 false *A 1.813,0.177 2.188,0.417 0.375,0.24 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ECU INTEGRATION BOX RH 82877 - - -
2 POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU - - - -
3 VEHICLE APPROACHING SPEAKER CONTROLLER 86572 - - -

*A for LHD *B for RHD

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during vehicle approaching speaker controller removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 82877 1.REMOVE ECU INTEGRATION BOX RH (for LHD)

Hide 2.REMOVE POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU (for RHD)

Hide 86572 3.REMOVE VEHICLE APPROACHING SPEAKER CONTROLLER

a.
E460279