| *1 | ECU INTEGRATION BOX LH | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>REMOVAL
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
55475B
3.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH
55431A
4.REMOVE INSTRUMENT PANEL FINISH PANEL
55432B
5.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL
55407B
6.REMOVE SWITCH HOLE BASE SUB-ASSEMBLY
58810J
7.REMOVE CONSOLE BOX ASSEMBLY
67914B
8.REMOVE FRONT DOOR SCUFF PLATE LH
62112
9.REMOVE COWL SIDE TRIM BOARD LH
62312B
10.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
55607
12.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55550
13.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
55433B
14.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
15.REMOVE POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU
Disengage the clamps.
| *A | for HV Model | - | - |
| *a | Lock Lever | - | - |
Disconnect the each connector.
Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.
for HV Model:
1. Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.
Remove the bolt and 2 nuts.
Using a screwdriver with its tip wrapped in protective tape, disengage the claws.
Disengage the claws.
| *a | Lock Lever | - | - |
Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.
Disconnect the connector to remove the power distribution box assembly with multiplex network body ECU.
82730G
16.REMOVE POWER DISTRIBUTION BOX ASSEMBLY
89221
17.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
|
Push |
|
Insert |
|
Raise |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) | - | - |
Press the claw of the power distribution box assembly as shown in the illustration to release the lock.
With the power distribution box assembly lock released, insert a screwdriver with its tip wrapped in protective tape horizontally between the main body ECU (multiplex network body ECU) and the power distribution box assembly.
Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).
Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).
Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.
Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).
Remove the main body ECU (multiplex network body ECU) as shown in the illustration.
Do not touch the main body ECU (multiplex network body ECU) connector.